Preparing and fixing the pots to the head of Rockets.
Preparing and fixing the pots to the head of Rockets.—Rockets which have furniture attached to them, are rammed somewhat different to those which are without any appendages, but the difference is only in this particular; when rammed one diameter above the piercer, instead of turning down upon the composition the inner folds of the paper, ram on to the composition one-third diameter of pure dry clay, and through the centre of it bore a hole (about one fourth diameter) and put into it a little of the composition, in order that the charge may communicate with the powder, &c. in the head.
The head of a Rocket must be about two diameters high, and one diameter one-sixth wide. The case must be rolled upon a former, having at the end opposite the handle a square indent, corresponding to the thickness and width of the collar, as is represented in [fig. 9. Fig. 10] is the collar, turned out of lime-tree, poplar, or any light wood; its exterior diameter must be equal to the interior diameter of the case, or the same as the former, and its interior diameter, not quite so wide as the interior diameter of the Rocket case; in thickness it should be equal to one-sixth diameter, and round its edge should be a groove, so that the case for the head may be firmly fixed to it. To form the case, three or four rounds of paper or pasteboard must be rolled round the former, with the collar on, and well secured by paste; the end over the collar is to be pinched by means of the cord and choaking apparatus into the groove in its edge, and afterwards secured by some twine tied closely round it. The purpose of the collar is to keep the head in a proper form, to make a bottom for the filling of it, and to make it more firm and better connected to the case. When the head is thus made, being properly fixed to its collar, it is to be made fast (by means of ordinary glue) to the top end of the Rocket, in which operation the reason and use of making the interior diameter of the collar less than the exterior of the cartridge will plainly appear; it will be evident that the cartridge of the Rocket will be too large for the former, without some alteration, which alteration must be made in the following manner:—mark round the diameter of the Rocket the proper distance from the top, or so that the collar is about its thickness above the ramming of the cartridge, and take off about three rounds of paper, which will leave a shoulder to the case, on which the collar may rest, and be made quite secure by pasting paper round their joinings beneath.
In the manner of charging the pot above described we must almost leave the Tyro to himself, it depending chiefly on his taste and wishes, as he may either fill it with Serpents, Crackers, Saucissons, Marroons, Stars, Sparks, Showers of Fire, or any thing to which its capacity is adapted; it will be best however to unite several of the different articles in one head that the beauty of the exhibition may be increased.
In the filling of the head, the following directions must be observed:—
The paper over the charge of the Rocket must be pierced, and a little of the same composition shook into the holes; then arrange in the head the different articles with which it is to be charged, but take particular care that the quantity introduced is not heavier than the body of the Rocket. When the head is loaded, a few balls of paper should be put round the different articles so as to keep them properly in their places. At the top part of each head put a ladle full of meal powder, (the ladle you use in filling the cases is meant,) which will be enough to burst the head and disperse the stars or whatever it contains.
In loading the head with cases of any kind be sure to place their mouths downward without any touch-paper; the head may be nearly filled, with the articles they are loaded with, after which paste on the top of them a piece of ordinary paper; and over this must be placed a cone of the same material, made upon the conical former, [fig. 8]. To make the caps, describe (with a pair of compasses opened to the length of the former) a circle, which being divided into two equal parts, will make two caps; over which must be pasted another similar cap, but of larger dimensions, so that it extend below the bottom of the inner one; so that being just clipped a little and applied to the head, it may be pasted to it, which will be a sufficient fastening.