It's Fun to Sew Aprons and Skirts

by Theta Johnson

Gathered skirt

Select fabric that is colorful and gay for your skirt. Closely woven cloth will be easy to sew and will hold a sharp crease.

You will need from 3 to 3½ yards of fabric for your skirt. The more fabric you try to gather in your skirt the harder it will be to make. For the girl of average height cut your skirt as follows:

How to cut your skirt

Cut or tear a 6½-inch strip from one side of your skirt fabric. Measure in from the selvage edge. Use this for the skirt band and pockets. There will be some left over.

Tear off the selvage edge from the large piece.

6½″ SELVAGE BAND POCKET POCKET CUT OR TEAR SELVAGE

You may have to cut the band from the end of your fabric instead of the side if you are tall and need the extra length.

The above method of cutting gives you one seam on the placket side.

Sometimes the design in the fabric will be more attractive if the skirt is cut in several lengths. When this is necessary, you will have three or four seams in your skirt. This may make a difference in the amount of fabric you will need, so decide how you will cut your skirt before buying your fabric.

Make your skirt

Pin the short edges together to make the side seam. Make the seam 1¼ inches wide. It is to be used for the placket. When finished, the placket will be on the left side.

Stitch the side seam. Stitch the seam from the bottom up. At a point 5 inches from the top, turn and stitch half way across the seam. Turn both edges of the seam toward the front section and press.

Trim the seams. Start at the bottom of the wide seam and trim it to ⅝ inch wide up to the placket. Do not trim above this point.

Finish the placket

1. Baste and stitch a ½-inch hem on the back edge of the placket.

2. Fold the front edge of the placket even with seam line. Press. Now fold again to make a complete hem. Baste.

Pin placket together. Stitch from the top to the bottom of the placket, turn and stitch across the end of first stitching. Pull threads through and tie ends. This is a strong, easy-to-make placket.

Hem the skirt

Skirts look best with hand-stitched hems. Make the hem before placing the band on the skirt. Unless you have poor posture, it will hang even. Decide how long you would like your finished skirt to be. Be careful not to make it too short. Measure from the top edge to the length you would like the skirt to be and press in the hem. Turn the top edge of the hem under ½ inch. Your skirt will be prettier if you make a wide hem—3 inches or wider.

When the hem has been carefully pressed, stitch ⅛ inch from the fold of the top edge of the hem, to keep the fold in place. Pin hem in place. Ask your leader to show you a hand hemming stitch.

Place gathering threads at top of skirt

Make a long stitch on your machine. Use size 50 top thread and heavy duty for bobbin thread.

Using the guide on your machine, stitch around the top of your skirt ¼ inch from the edge. Make two more rows ¼ inch apart. You are now ready to make your skirt band.

Make the skirt band

1. Measure your waist. Add 2½ inches. This will give you the length needed for your skirt band. Cut your band 6½ inches wide.

2. Press a ½-inch fold along one side of your band. From the folded edge divide the rest into three sections. This gives three 2-inch sections. Make the section with the ½-inch fold slightly shorter than the other two sections. Press.

3. The section with the ½-inch fold is the front of your band. Stitch criss-cross through the back part of the band. You can stitch straighter if you make a guide or pattern. Cut a strip of waxed paper the length and width of your band, 24 x 2 inches.

Fold it in six equal sections. Then fold it diagonally. Then diagonally again. Open the paper and pin it to the band and follow the creases in the paper. This will give practice on starting and stopping the machine and on turning corners. Tear the paper away after the stitching is completed.

4. Stitch a ½-inch seam at the ends of the band. Turn and press. Do not sew the ½-inch fold at the bottom of band into the seam.

Gather in fullness

Divide both your skirt and the skirt band into eight equal parts to help you make the gathers even in your skirt. Do not include the placket or 1-inch overlap at the end of the band. Mark with colored threads. Mark the skirt band so the extension or extra length will be on the back of the placket. The front of band will be even with the front edge of the placket.

Pin and stitch band to skirt.

Pin the pieces together, right side of skirt to right side of band. Match dividing marks that you have made. Gently pull on the gathering threads at the side seams, the center front, and the center back. Pull the threads until they are the same length as the band. Work with the gathers until they are even. Baste and stitch along ½-inch fold on the skirt band.

Top stitch the band

Fold the double section of your band toward the back and baste the edge of the band to the skirt. Baste it so the folded edge hangs just below the stitching you just made on the front side of the band. Machine stitch from the front side of the band. Place the stitching as near the edge of the band as you can. Press before you stitch. It will flatten the seam and make stitching easier.

Press your skirt

Press your skirt. Use a dampened cheese-cloth and an iron set for ironing cotton, or use a steam iron. A skirt must be well pressed and fresh looking to be pretty.

Fastenings for the skirt

Study the drawing above. It shows the placing for fasteners on your skirt. Sewing them in this position will keep the placket from gaping. Sew a snap fastener in the center of the placket if it is needed to keep it closed. Do not try to set in a zipper. Use hooks and eyes or buttons for fastening this band.

Buttons and buttonholes—When buttons and buttonholes are used, make the buttonhole lengthwise of the band. Place it far enough from the end of the band so there will be at least ¼ inch beyond the button when it is sewed in place. Measure half the distance across your button and add ¼ inch for this measurement.

Learn to use the machine attachment for making buttonholes. They are stronger and easier for you to make than hand-made buttonholes. Have your leader, mother, or a neighbor set it up for you and show you how to use it. After you have made a few sample buttonholes, make some in your apron or on your skirt. If you have a machine with a zig-zag stitch, learn to make buttonholes on it.

Pin the band together and mark place for buttons. See [page 2] for instructions for sewing on buttons.

Sew fasteners to skirt band

Snaps—Examine the snap fasteners. One part has a ball on top. This is placed on the front part or top of your placket. The other part has a hole or socket and is placed on the back or under part of the placket. Place them exactly opposite each other on your placket.

Sew the top snap on first. Mark the placing of the bottom part of the snaps by rubbing chalk on the ball and then pinning placket together. Press ball against fabric. The chalk will rub off and mark the exact spot to sew the under part of the snap.

Sew snap fasteners on with several over-and-over stitches. Be sure to hide your knot under the snap. Sew securely through all four holes. When you cross from one hole to the other, take a stitch in the cloth and bring your needle up from the under side to the next hole.

Hooks and eyes—Each package of hooks and eyes, has two types of eyes, a round and a straight. Use the round eye for your skirt. Sew the hook on the inside edge of the top part of your band. (You will need two.) Sew these with several over-and-over stitches.

Sew several stitches through the hook end. Pin the placket in place and place the round eye directly under the hook. Sew with several over-and-over stitches.

Press all the things you have made. Pressing will improve their appearance. Make sure they are clean.

Have each member of your club judge what you have made and then make the corrections they suggest.