TABLE 1.—Summary of Results of Transverse Tests of Beams at Tulane University, February 10th to March 2d, 1909.

Number of beam.	Top or butt of log.	b	h	I	Loads:		S = Plc/4I		d, Inches.	E	Weight, in pounds per cubic foot.	Remarks.
Number of beam.	Top or butt of log.	Width, in inches.	Height, in inches.	I = bh³/12	Actual at elastic limit.	Maximum.	At elastic limit.	Maximum.	At elastic limit.	E = Pl³/48dI	Weight, in pounds per cubic foot.	Remarks.
I	B	6.28	15.94	2,120	22,000	45,900	2,975	6,200	0.41	1,575,000	50.2	Close-grained pine, long-leaf.
I	T	6.00	15.69	1,934	20,000	38,000	2,915	5,540	0.465	1,383,000	47.5	Close-grained pine, long-leaf.
II [A]	T	6.37	15.81	2,098	20,000	43,450	2,722	5,918	0.380	1,562,000	40.5	Coarse loblolly, large knots.
II	B	6.41	16.41	2,360	16,000	25,040	1,999	3,130	0.430	979,000	42.2	Coarse loblolly, large knots.
III	T	5.88	15.68	1,871	24,000	45,130	3,608	6,785	0.535	1,489,000	40.4	Close-grained, long-leaf no knots.
III	B	5.88	15.90	1,965	21,000	35,190	3,054	5,120	0.515	1,288,000	44.2	Close-grained, long-leaf no knots.
IV	T	6.00	15.43	1,835	22,000	38,425	3,320	5,810	0.465	1,601,000	40.8	Loblolly, with knots.
IV	B	6.12	15.87	2,032	22,000	35,500	3,090	4,983	0.660	1,017,000	41.5	Loblolly, with knots.
V	B	6.00	16.00	2,048	22,000	47,000	3,090	6,610	0.400	1,670,000	47.2	Long-leaf yellow pine.
V[A]	T	6.00	15.87	1,999	14,000	22,050	1,998	3,145	0.315	1,382,000	42.1	Long-leaf yellow pine.
VI[A]	B	5.50	15.75	1,790	22,000	51,330	3,484	8,925	0.450	1,695,000	50.2	Long-leaf yellow pine.
VI[A]	T	5.87	15.62	1,865	20,000	44,000	3,013	6,627	0.410	1,625,000	45.2	Long-leaf yellow pine.
VII	B	6.56	15.62	2,083	34,000	51,900	4,580	6,985	0.620	1,637,000	43.7	Long-leaf yellow pine.
VII[A]	T	6.22	15.62	1,975	20,000	49,000	2,845	6,970	0.380	1,658,000	40.2	Long-leaf yellow pine.

[A] Failed in longitudinal shear.

The deflection was measured on both sides of each beam by using silk threads stretched on each side from nails driven about 2 in. above the bottom of the beam and directly over the rollers which formed the supports. From a small piece of wood, tacked to the bottom of the beam at its center and projecting at the sides, the distance to these threads was measured. These measurements were taken to the nearest hundredth of an inch. The mean of the deflections was taken as the true deflection for any load.

Fig. 3.—DEFLECTON CURVES BEAM III

Fig. 4.—DEFLECTON CURVES BEAM IV

In computing the various quantities shown in Table 1, the summary of results, the load has been assumed as concentrated at the center of the beam. While it is true that the load was spread over a length of about 12 in., due to the width of the head of the machine and the plate between it and the beam tested, it is also true that there were irregularities, such as bolt-holes and, in some cases, abrasions due to wear, that could not well be taken into account. Hence, it was deemed sufficiently accurate to consider the load as concentrated. Besides the horizontal bolt-holes, shown in the photographs, there were vertical bolt-holes, at intervals in all the beams. The latter were 7/8 in. in diameter, and in every case they were sufficiently removed from the center of the length of the beam to allow the maximum moment at the reduced section to be relatively less than that at the center of the beam. For this reason, no correction was made for these holes. The broken beams often showed that rupture started at, or was influenced by, some of the holes, especially the horizontal ones.

While some of the heavy oils of a tarry consistency remained, they were only to be found in the sappy portions of the long-leaf pine and in the loblolly (Specimens II and IV). Exposure in a semi-tropical climate for 26 years had resulted in the removal of the more volatile portions of the creosote oil. The penetration of the oil into the sap wood seemed to be perfect, while in the loblolly it varied from a fraction of an inch to 1-1/2 in. In the heart wood there was very little penetration across the grain. The timber had been framed and the holes bored before treatment. The penetration of the creosote along the grain from the holes was often from 4 to 6 in.

Circular 39 of the Forest Service, U. S. Department of Agriculture, entitled "Experiments on the Strength of Treated Timber," gives the results of a great many tests of creosoted ties, principally loblolly pine, from which the following conclusions are quoted:

"(1) A high degree of steaming is injurious to wood. The degree of steaming at which pronounced harm results will depend upon the quality of the wood and its degree of seasoning, and upon the pressure (temperature) of steam and the duration of its application. For loblolly pine the limit of safety is certainly 30 pounds for 4 hours, or 20 pounds for 6 hours." [Tables 3, 6, and 7.]

"(2) The presence of zinc chlorid will not weaken wood under static loading, although the indications are that the wood becomes brittle under impact." [Tables 3 and 4.]

Fig. 5.—DEFLECTON CURVES BEAM V

Fig. 6.—DEFLECTON CURVES BEAM VI

"(3) The presence of creosote will not weaken wood of itself. Since apparently it is present only in the openings of the cells, and does not get into the cell walls, its action can only be to retard the seasoning of the wood." [Tables 3, 4, 5, and 6.]

Fig. 7.—DEFLECTON CURVES BEAM VII

Comparisons.

A comparison of the results obtained with tests made on untreated timber is interesting, and to this end Tables 2 and 3, from Circular 115, Forest Service, U.S. Department of Agriculture, by W. Kendrick Hatt, Assoc. M. Am. Soc. C. E., are quoted. The tests made by the writer were from timber raised in Louisiana and Mississippi, while the tests quoted were from timber raised farther north. The number of tests was not sufficient to settle questions of average strength or other qualities. It will be seen, however, that the treated timber 26 years old compares favorably with the new untreated timber.

Plate I, Fig. 1.—Specimen in Testing Machine, Showing Method of Support.

Plate I, Fig. 2.—End Views of Tested Timbers.