A patent was likewise obtained in 1800 by Mr. Ebenezer Palmer, a London stationer, for an improved way of binding books, particularly merchants’ account-books. This improvement has been described as follows:—let several small bars of metal be provided about the thickness of a shilling or more, according to the size and thickness of the book; the length of each bar being from half an inch to several inches, in proportion to the strength required in the back of the book. At each end of every bar let a pivot be made of different lengths, to correspond to the thickness of two links which they are to receive. Each link must be made in an oval form, and contain two holes proportioned to the size of the pivots, these links to be the same metal as the hinge, and each of them nearly equal in length to the width of two bars. The links are then to be riveted on the pivots, each pivot receiving two of them, and thus holding the hinge together, on the principle of a link-chain or hinge. There must be two holes or more of different sizes, as may be required, on each bar of the hinge or chain; by means of these holes each section of the book is strongly fastened to the hinge which operates with the back of the book, when bound, in such a manner as to make the different sections parallel with each other, and thus admit writing without inconvenience on the ruled lines, close to the back.
The leather used in covering books is prepared and applied as follows: being first moistened in water, it is cut to the size of the book, and the thickness of the edge is paired off on a marble stone. It is next smeared over with paste made of wheat flour, stretched over the pasteboard on the outside, and doubled over the edges within. The book is then corded, that is, bound firmly betwixt two boards, to make the cover stick strongly to the pasteboard and the back; on the exact performance of which the neatness of the book in a great measure depends. The back is then warmed at the fire to soften the glue, and the leather is rubbed down with a bodkin or folding stick, to set and fix it close to the back of the book. It is now set to dry, and when dry the boards are removed; the book is then washed or sprinkled over with a little paste and water, the edges and squares blacked with ink, and then sprinkled fine with a brush, by striking it against the hand or a stick; or with large spots, by being mixed with solution of green vitriol, which is called marbling. Two blank leaves are then pasted down to the cover, and the leaves, when dry, are burnished in the press, and the cover rolled on the edges. The cover is now glazed twice with the white of an egg, filleted, and last of all, polished, by passing a hot iron over the glazed colour.
The employment in book binding of a rolling press for smoothing and condensing the leaves, instead of the hammering which books have usually received, is an improvement introduced several years ago into the trade by Mr. W. Burn. His press consists of two iron cylinders about a foot in diameter, adjustable in the usual way, by means of a screw, and put in motion by the power of one man or of two, if need be, applied to one or two winch-handles. In front of the press sits a boy who gathers the sheets into packets, by placing two, three, or four upon a piece of tin plate of the same size, and covering them with another piece of tin plate, and thus proceeding by alternating tin plates and bundles of sheets till a sufficient quantity have been put together, which will depend on the stiffness and thickness of the paper. The packet is then passed between the rollers and received by the man who turns the winch, and who has time to lay the sheets on one side, and to hand over the tin plates by the time that the boy has prepared a second packet. A minion bible may be passed through the press in one minute, whereas the time necessary to beat it would be twenty minutes. It is not, however, merely a saving of time that is gained by the use of the rolling press; the paper is made smoother than it would have been by beating, and the compression is so much greater, that a rolled book will be reduced to about five-sixths of the thickness of the same book if beaten. A shelf, therefore, that will hold fifty books bound in the usual way would hold nearly sixty of those bound in this manner, a circumstance of no small importance, when it is considered how large a space even a moderate library occupies, and that book-cases are an expensive article of furniture. The rolling press is now substituted for the hammer by several considerable bookbinders.
[Fig. 141.] represents the sewing press, as it stands upon the table, before which the bookbinder sits. [Fig. 142.] is a ground plan without the parts a and n in the former figure. A is the base-board, supported upon the cross bars m n, marked with dotted lines in [fig. 142.] Upon the screw rods r r [fig. 141.] the nuts t d serve to fix the flat upper bar n, at any desired distance from the base. That bar has a slit along its middle, through which the hooks below z z pass down for receiving the ends of the sewing cords p p, fixed at y y, and stretched by the thumb-screws z z. The bar y y is let into an oblong space cut out of the front edge of the base board and fixed there by a movable pin a, and a fixed pin at its other end round which it turns.
[Fig. 143.] is the bookbinder’s cutting press, which is set upright upon a sort of chest for the reception of the paper parings; and consists of three sides, being open above and to the left hand of the workman. The pressbar, or beam a, has two holes n n upon its under surface, for securing it to two pegs standing on the top of the chest. The screw rods t t pass through two tapped holes in the bar, marked with b c at its upper end; their heads r r being held by the shoulders o o. The heads are pierced with holes into which lever pins are thrust for screwing the rods hard up. The heavy beam a remains immovable, while the parallel bar with the book is brought home towards it by the two screws. The two rulers s s serve as guides to preserve the motions truly parallel; and the two parallel lath bars b c guide between them the end bar e, of the plough, whose knife is shown at i, with its clamping screw z.