[Fig. 503.] and [504.] represent a Bohemian furnace in which excellent white window glass is founded. [Fig. 503.] is a longitudinal section of the glass and annealing furnace. [Fig. 504.] is the ground plan. a is the ash pit vaulted under the sole of the furnace; the fireplace itself is divided into three compartments; with a middle slab at d, which is hollowed in the centre, for collecting any spilt glass, and two hearth tiles or slabs b b. c c are the draught or air holes; e e are arches upon which the bearing slabs f f partly rest. In the middle between these arches, the flame strikes upwards upon the pots g g, placed as closely together as possible, for economy of room. h is the breast wall of the furnace; i, [fig. 504.], the opening through which the pots are introduced; it is bricked up as soon as they are set. k k, is the base of the cone or dome of the furnace; l l l, the working orifices, which are made larger or smaller according to the size of the glass articles to be made. m is the flue which leads to the annealing stove n, with an arched door. Exterior to this, there is usually a drying kiln not shown in the figure; and there are adjoining stoves called arches, for drying and annealing the new pots before they are set.
The cooling or annealing arch, or leer, is often built independent of the glass-house furnace, is then heated by a separate fire-place, and constructed like a very long reverberatory furnace. See [Copper].
The leer pans or trays of sheet iron, are laid upon its bottom in an oblong series, and hooked to each other.
3. Crown-glass.—The crown-glass house with its furnace is represented in [fig. 505.], where the blowing operation is shewn on the one side of the figure, and the flashing on the other. The furnace is usually constructed to receive 4 or 6 pots, of such dimensions as to make about a ton of glass each at a time. There are, however, several subsidiary furnaces to a crown-house. 1. A reverberatory furnace or calcar, for calcining or fritting the materials; 2. a blowing furnace, for blowing the pear-shaped balls made at the pot-holes, into large globes; 3. a flashing furnace, and bottoming hole for communicating a softening heat, in expanding the globe into a circular plate; 4. the annealing arch for the finished tables; 5. the reverberatory oven for annealing the pots prior to their being set upon the founding siege.
The materials of crown glass used to be, fine sand, by measure 5 parts, or by weight 10; ground kelp by measure 11 parts, or by weight 161⁄2; but instead of kelp, soda ash is now generally employed. From 6 to 8 cwt. of sand, lime, and soda-ash, mixed together in wooden boxes with a shovel, are thrown on the sole of a large reverberatory, such as is represented in the article [Copper]. Here the mixture is well worked together, with iron paddles, flat shovels, and rakes with long handles; the area of this furnace being about 6 feet square, and the height 2 feet. The heat soon brings the materials to a pasty consistence, when they must be diligently turned over, to favour the dissipation of the carbon, sulphur, and other volatile matters of the kelp or soda ash, and to incorporate the fixed ingredients uniformly with the sand. Towards the end of 3 hours, the fire is considerably raised, and when the fourth hour has expired, the fritting operation is finished. The mass is now shovelled or raked out into shallow cast-iron square cases, smoothed down, and divided before it hardens by cooling, into square lumps, by cross sections with the spade. These frit-bricks are afterwards piled up in a large apartment for use; and have been supposed to improve with age, by the efflorescence of their saline constituents into carbonate of soda on their surface.
The founding-pots are filled up with these blocks of frit, and the furnace is powerfully urged by opening all the subterranean passages to its grate, and closing all the doors and windows of the glass-house itself. After 8 or 10 hours the vitrification has made such progress, and the blocks first introduced are so far melted down, that another charge of frit can be thrown in, and thus the pot is fed with frit till the proper quantity is used. In about 16 hours the vitrification of the frit has taken place, and a considerable quantity, amounting often to the cwt. of liquid saline matter floats over the glass. This salt is carefully skimmed off into iron pots with long ladles. It is called Sandiver or Glass-gall, and consists usually of muriate of soda, with a little sulphate. The pot is now ready for receiving the topping of cullet, which is broken pieces of window glass, to the amount of 3 or 4 cwt. This is shovelled in at short intervals; and as its pressure forces up the residuary saline matter, this is removed; for were it allowed to remain, the body of the glass would be materially deteriorated.
The heat is still continued for several hours till the glass is perfect, and the extrication of gas called the boil, which accompanies the fusion of crown glass, has nearly terminated, when the fire is abated, by shutting up the lower vault doors and every avenue to the grate, in order that the glass may settle fine. At the end of about 40 hours altogether, the fire being slightly raised by adding some coals, and opening the doors, the glass is carefully skimmed, and the working of the pots commences.