Woodcraft

by Elmer Harry Kreps

Did you ever wonder why an ax handle is curved in an S shape? It is made to fit the hands of the user without strain on the arms or wrists, and this curved shape enables him to hold the ax more solidly when striking a blow than could be done with a straight handle. The handle should be quite thick and "hand-fitting" near the end where it is grasped by the left hand (or right, according to whether the user is right or left handed), but the other part should be shaped so the hand can slide easily back and forth while chopping.

The handle should be fastened into the ax with a wedge, which in turn is held in place by a screw. The wedge has a head so that when the screw is removed it is easily pried out, and then if it is necessary to remove the handle the ax can be driven into the top of a stump or into a log, and the handle easily detached. Such wedges may be bought from almost any hardware company.

This is my idea of what a woodsman's ax should be, and such a tool weighing two pounds, with a well-shaped handle thirty or thirty-two inches long from the end to the ax eye makes an efficient tool of light weight and a great article for use on the trail or trap line. I might say of it, as Davy Crockett said of his knife: "It will jump higher, dive deeper, shave more hogs and stand more bending without breaking than any other made."

As nearly all woodsmen are good axmen, it may seem superfluous to give advice regarding the care of an ax, the way to grind it, and how to use it, but this article is not intended for those who know, but for these who do not, and are desirous to learn. By a reckless, careless blow at a hemlock knot I have seen the entire bit broken off an ax, while other axes of no better temper but properly ground and well handled have gone through an entire season of "bark peeling" without a nick of any consequence. I have seen axes ruined in a half day's work cutting brush close to the ground, and have myself used an ax day after day at the same kind of work without making a nick which could not be whetted out in a few minutes with a small ax stone.

There is also a lot of danger in the careless use of an ax. I have known of at least two men who have cut their heads by splitting wood under a clothes line. The same thing may happen when working under a tree with low, drooping branches. In the woods it will pay double to make it a rule on every occasion to be sure that there is not even the smallest twig in the way to catch the ax before you make a stroke with it. Trim all brush away from around a tree before you commence to cut it, and observe the same precautions when you cut it into lengths or when lopping the branches. When cutting the fallen tree into lengths, the common and most convenient way is to stand on the log and chop it half way through between the feet, then turn and cut the other side in the same way. Use double precaution when doing this, for I have known of an ax being deflected and a nasty cut being the result. It seems that the smallest branch or sprout can turn the ax toward the foot of the chopper.

When chopping down timber the tree can nearly always be thrown either of three ways — the way the tree inclines or to either side, but not the opposite way from its inclination. In addition to the incline of the tree, the influence of the wind and the weight of the branches must be considered, and when all of these forces are brought to bear the timber cutter must be well "onto his job" to know just how to cut the tree to make it fall in the desired direction. A good chopper, however, can throw the tree to any spot designated within the falling zone almost every time. The wind is a great factor and must be considered, especially when the breeze is strong or when the tree appears to stand perfectly straight. A tree on a slope that appears to be perpendicular will, in nearly every case, fall down hill if free to fall as it wills, providing there is no contrary wind. If the tree really stands perfectly upright and there is no wind, it will fall best toward the side that has the most branches, or to the side having the greatest weight. If allowance must be made, however, for both wind and gravity, it is then the judgment of the chopper is put to the test. If he can estimate accurately the power of each of these forces, he can drop his tree exactly where he wants to, but how?

It is very simple. In cutting a tree a notch is cut on the side toward which the tree is to fall. Remember that this notch should be cut into the center of the tree, and when finished, should be exactly at a right angle to the line on which the tree is to fall. A notch is then cut on the opposite side, just a little higher on the tree, and when this notch is cut in almost to the center the tree will fall. If the tree is notched to fall the way it inclines and there is nothing to prevent it going that way, the second notch should be cut exactly parallel to the first. If, however, the tree leans a little to one side, if there are more branches on that side, or if the wind blows in that direction, the second cut should not be parallel with the first, but should be farther from it on the side from which the wind comes, so that there will be more wood to break on that side. In no case should the notches entirely meet on the other side, for if they do, should the tree be cut entirely off on one side, it will settle farther over to that side. Just how near you dare cut it off on the one side and how much you must hold on the opposite side can be learned only from experience.

There are other little things that have a certain amount of influence. For instance, if there is nothing to interfere, the tree in falling will draw slightly toward the high side of the notch first cut. Then, too, if the notch is not perfectly cut, if it is more acute on one side than on the other, as the tree falls the top and bottom of the notch will meet on one side before they do on the other, and this is certain to swing the tree slightly toward the wide or obtuse side of the notch. A heavy weight of branches, too, on one side may cause the tree to roll slightly in falling.

For your own safety it is always best to get back a safe distance from the tree when it starts to fall, because if it falls over a rock, a log, or a little rise in the ground the butt of the tree will kick and may lift your head off, which would be decidedly unpleasant. If there are other trees in the way, look out for falling branches.

I have already told how to cut the tree in sections, but the branches must be trimmed off before it can be cut up entirely. In trimming, work from the butt toward the top, as the branches usually grow that way, cut easier, and are not in the way while chopping. Hold the ax rigidly when trimming, as the knots are likely to be hard and an ax that is not held firmly may break or bend. Make it a rule to do no more trimming than necessary on such woods as hemlock and fir, which have very hard knots. Frozen wood is also likely to break the ax.