Woodcraft

by Elmer Harry Kreps

On the spot chosen for the camp we now place two of the long logs, parallel with each other and exactly ten feet apart. We block them on the outside so they cannot be moved easily out of position. Then we place two of the short logs across the ends and in these we cut half-round notches directly over the places where they rest on the long logs, and almost half through each piece. After cutting these notches we turn the logs notched side down, and these cuts, if they have been properly done, fit snugly over the long logs, thus binding the four pieces together and forming the first round of the walls.

Before going farther now we must decide just where we are going to have the doorway of our cabin. We will place it on the south side, for we like to have the warm sun rays come in when the door is open, and if placed on the north or west sides it admits too much cold. We will place it near one end and then we can also put our window in the same side. About two or three feet from the corner we will cut out a section from the top of the log, making the cut four inches deep and two and a half feet wide, the bottom being hewn smooth and the ends sawed down square. Then we cut one of the balsam trees and saw a section from the butt the length of the proposed doorway. This should be not less than five feet, so we make it this length. Then we split through the centre with the axe and a pair of wooden wedges, and hew the two halves into two smooth planks. We also make a plank two and a half feet long. When these planks are finished we stand the two long ones upright in the place cut in the log and nail them firmly. We see that they stand perfectly plumb and in line with one another, then we nail the short plank across the top, thus completing our doorway. On this side, as the walls are laid up, we saw each log off squarely at the proper place and push it up against the door frame, fastening it there by nailing through the plank. The notches are cut to such a depth at the corners that the logs fit one against the other and this leaves no large cracks to close.

To make our cabin comfortable it must have a floor and we have this in mind as we work. Before building the wall higher we will lay our sills for the floor, for it is difficult to get these cut to the proper length and fitted in place after the walls are completed and the timber must be brought in through the doorway. We cut three straight logs about eight inches thick in the middle and 14 feet long. These are bedded into the ground in the cabin, one along each side wall and the other in the centre. They must be placed at an even height and this is determined by means of a straight ten-foot pole, which when placed across these logs should rest on each. If one of them is too high in spots we dress these places down with the axe.

We will now leave the floors and proceed with building the walls. Round by round the logs are notched and fitted into place, until the walls have reached a height of about four feet. Then we make a window boxing of planks and fasten it in the wall in the same way we did the door frame. The ends of the logs are butted against the window frame and fastened with large nails, driven through the planks into the logs. But before making the window frame the size of the proposed window must be determined, and this is done by measuring the width of the glass and making the proper allowance for the sash. When the logs are placed in the walls we try to select timbers of such a size that one round of logs will come within about three inches of the top of the window boxing, and the next log is cut out to fit down over this window and the frame is nailed fast to this log. The same thing is done when the top of the door frame is reached, and this gives a greater degree of rigidity to the walls.

When the walls have been raised to a height of about six and a half feet above the floor sills we commence work on the gables. These are constructed by placing a full length log across the end, a shorter one on top of this, continuing thus until high enough. This is best done by setting a pole up in the end of the camp exactly in the middle of the end wall, the top being just the height of the proposed gable. From the top of this straight pole, poles are run down to each corner and these give the slope of the gables, also of the roof. The logs are then cut off on an incline at the ends to conform with the line of this pole, and are fastened one on top of another by boring holes and driving wooden pins into them. When both gables have been raised to half their height we cut two 17-foot binding poles, each six inches thick in the middle, and notch them into the logs of the gables. These logs or poles not only give more stability to the gables, but they also make a support for the roof, and are a nice foundation for a loft on which to store articles after the camp is finished. When the ends are brought up to within about eight inches of the required height a stout, straight ridge pole of the same length as the binding poles is placed on top, and notched lightly into the top log.

Our camp is now ready for the roof, and what are we to use for this most important part. I have no doubt that camp roofs have caused more gray hairs for woodsmen than any of the other problems they have to solve. If it were early summer when the bark could be peeled from cedar and spruce trees we would have no trouble, but bark is not available now. About the only style of roof that we can make now is what is called a scoop roof, made from split logs. We must find a straight-grained, free-splitting wood for this, and of the woods at hand we find balsam the best, so we cut balsam trees about eight or ten inches in diameter, and make logs from the butt of each, about seven feet long, so that they will reach from the top of the ridge-pole to the walls and extend a foot beyond. These we split through the centre and hollow out each in a trough form, by cutting notches in the flat side, without cutting the edges, and splitting out the sections between. We place a layer of these the entire length of the roof, hollow side up, and notch each in place so that it cannot slip or rock. Between each set of these troughs we will place a three-inch pole, and on top of the pole we place marsh moss. Then we place over these poles a second layer of the troughs, hollow side down, and over the ridge pole we place a large, full-length trough. This latter we must make by hewing a log flat on one side and then hollowing it out, for we cannot find a tree with such a straight grain that we can split a 17-foot length without more or less of a twist.

Before completing our roof, in fact when the first layer of scoops are placed on, we must make provision for our stove pipe, for it must have an outlet through the roof, and the location the stove is to have in the cabin must be determined. A hole 12 or 14 inches square is left in the roof, by using a few short scoops, and this hole is covered with the sheet of tin we brought for the purpose, and a slightly oblong hole is cut in this for the stove pipe. The edge of this hole we turn up with the hammer, which makes it waterproof, and when finished it is such a size that the pipe makes a snug fit. The whole thing is so arranged that water cannot run under from the top, but this is difficult to explain.