The Principles of Scientific Management

by Frederick Winslow Taylor

Third. That the most friendly relations existed between the management and the employees, which rendered labor troubles of any kind or a strike impossible.

These good results were brought about by many changes which substituted favorable for unfavorable working conditions. It should be appreciated, however, that the one element which did more than all of the others was, the careful selection of girls with quick perception to replace those whose perceptions were slow—(the substitution of girls with a low personal coefficient for those whose personal coefficient was high)—the scientific selection of the workers.

The illustrations have thus far been purposely confined to the more elementary types of work, so that a very strong doubt must still remain as to whether this kind of cooperation is desirable in the case of more intelligent mechanics, that is, in the case of men who are more capable of generalization, and who would therefore be more likely, of their own volition, to choose the more scientific and better methods. The following illustrations will be given for the purpose of demonstrating the fact that in the higher classes of work the scientific laws which are developed are so intricate that the high-priced mechanic needs (even more than the cheap laborer) the cooperation of men better educated than himself in finding the laws, and then in selecting, developing, and training him to work in accordance with these laws. These illustrations should make perfectly clear our original proposition that in practically all of the mechanic arts the science which underlies each workman's act is so great and amounts to so much that the workman who is best suited to actually doing the work is incapable, either through lack of education or through insufficient mental capacity, of understanding this science.

A doubt, for instance, will remain in the minds perhaps of most readers (in the case of an establishment which manufactures the same machine, year in and year out, in large quantities, and in which, therefore, each mechanic repeats the same limited series of operations over and over again), whether the ingenuity of each workman and the help which he from time to time receives from his foreman will not develop such superior methods and such a personal dexterity that no scientific study which could be made would result in a material increase in efficiency.

A number of years ago a company employing about three hundred men, which had been manufacturing the same machine for ten to fifteen years, sent for us to report as to whether any gain could be made through the introduction of scientific management. Their shops had been run for many years under a good superintendent and with excellent foremen and workmen, on piece work. The whole establishment was, without doubt, in better physical condition than the average machine-shop in this country. The superintendent was distinctly displeased when told that through the adoption of task management the output, with the same number of men and machines, could be more than doubled. He said that he believed that any such statement was mere boasting, absolutely false, and instead of inspiring him with confidence, he was disgusted that any one should make such an impudent claim. He, however, readily assented to the proposition that he should select any one of the machines whose output he considered as representing the average of the shop, and that we should then demonstrate on this machine that through scientific methods its output could be more than doubled.

The machine selected by him fairly represented the work of the shop. It had been run for ten or twelve years past by a first-class mechanic who was more than equal in his ability to the average workmen in the establishment. In a shop of this sort in which similar machines are made over and over again, the work is necessarily greatly subdivided, so that no one man works upon more than a comparatively small number of parts during the year. A careful record was therefore made, in the presence of both parties, of the time actually taken in finishing each of the parts which this man worked upon. The total time required by him to finish each piece, as well as the exact speeds and feeds which he took, were noted and a record was kept of the time which he took in setting the work in the machine and removing it. After obtaining in this way a statement of what represented a fair average of the work done in the shop, we applied to this one machine the principles of scientific management.

By means of four quite elaborate slide-rules, which have been especially made for the purpose of determining the all-round capacity of metal-cutting machines, a careful analysis was made of every element of this machine in its relation to the work in hand. Its Pulling power at its various speeds, its feeding capacity, and its proper speeds were determined by means of the slide-rules, and changes were then made in the countershaft and driving pulleys so as to run it at its proper speed. Tools, made of high-speed steel, and of the proper shapes, were properly dressed, treated, and ground. (It should be understood, however, that in this case the high-speed steel which had heretofore been in general use in the shop was also used in our demonstration.) A large special slide-rule was then made, by means of which the exact speeds and feeds were indicated at which each kind of work could be done in the shortest possible time in this particular lathe. After preparing in this way so that the workman should work according to the new method, one after another, pieces of work were finished in the lathe, corresponding to the work which had been done in our preliminary trials, and the gain in time made through running the machine according to scientific principles ranged from two and one-half times the speed in the slowest instance to nine times the speed in the highest.

The change from rule-of-thumb management to scientific management involves, however, not only a study of what is the proper speed for doing the work and a remodeling of the tools and the implements in the shop, but also a complete change in the mental attitude of all the men in the shop toward their work and toward their employers. The physical improvements in the machines necessary to insure large gains, and the motion, study followed by minute study with a stop-watch of the time in which each workman should do his work, can be made comparatively quickly. But the change in the mental attitude and in the habits of the three hundred or more workmen can be brought about only slowly and through a long series of object-lessons, which finally demonstrates to each man the great advantage which he will gain by heartily cooperating in his every-day work with the men in the management. Within three years, however, in this shop, the output had been more than doubled per man and per machine. The men had been carefully selected and in almost all cases promoted from a lower to a higher order of work, and so instructed by their teachers (the functional foremen) that they were able to earn higher wages than ever before. The average increase in the daily earnings of each man was about 35 per cent., while, at the same time, the sum total of the wages paid for doing a given amount of work was lower than before. This increase in the speed of doing the work, of course, involved a substitution of the quickest hand methods for the old independent rule-of-thumb methods, and an elaborate analysis of the hand work done by each man. (By hand work is meant such work as depends upon the manual dexterity and speed of a workman, and which is independent of the work done by the machine.) The time saved by scientific hand work was in many cases greater even than that saved in machine-work.

It seems important to fully explain the reason why, with the aid of a slide-rule, and after having studied the art of cutting metals, it was possible for the scientifically equipped man, who had never before seen these particular jobs, and who had never worked on this machine, to do work from two and one-half to nine times as fast as it had been done before by a good mechanic who had spent his whole time for some ten to twelve years in doing this very work upon this particular machine. In a word, this was possible because the art of cutting metals involves a true science of no small magnitude, a science, in fact, so intricate that it is impossible for any machinist who is suited to running a lathe year in and year out either to understand it or to work according to its laws without the help of men who have made this their specialty. Men who are un-familiar with machine-shop work are prone to look upon the manufacture of each piece as a special problem, independent of any other kind of machine-work. They are apt to think, for instance, that the problems connected with making the parts of an engine require the especial study, one may say almost the life study, of a set of engine-making mechanics, and that these problems are entirely different from those which would be met with in machining lathe or planer parts. In fact, however, a study of those elements which are peculiar either to engine parts or to lathe parts is trifling, compared with the great study of the art, or science, of cutting metals, upon a knowledge of which rests the ability to do really fast machine-work of all kinds.

The real problem is how to remove chips fast from a casting or a forging, and how to make the piece smooth and true in the shortest time, and it matters but little whether the piece being worked upon is part, say, of a marine engine, a printing-press, or an automobile. For this reason, the man with the slide rule, familiar with the science of cutting metals, who had never before seen this particular work, was able completely to distance the skilled mechanic who had made the parts of this machine his specialty for years.