(1) The “metal” is made by fusing animal matters with pearlash, almost invariably with the addition of iron scrap. The animal substances are sometimes used in their original condition, whilst sometimes they are previously charred. Generally speaking, however, a judicious mixture of the fresh and charred materials has been found to give the best results. The charcoal which is left on carbonising animal matters contains a certain amount of nitrogen, decreasing in proportion as the temperature rises; but a smaller quantity of charcoal is also thereby produced. For example: 100 parts of rags carbonised at a certain temperature left 75 parts charcoal containing 12 per cent. of nitrogen, while the same rag carbonised at a higher temperature yielded 25 parts of charcoal, which contained only 2 per cent. of nitrogen. The animal matters employed should not leave much ash on ignition, as this would both thicken the mass and decompose a portion of the potash. In this respect sand is specially objectionable, for on ignition 1 part will decompose 2 of pearlash, owing to formation of silicate of potash. It is not necessary that the pearlash should be quite pure; in fact, a certain proportion of sulphate is stated to be useful, as it is changed into sulphide by ignition with the carbonaceous materials.

The theory of the formation of yellow prussiate of potash may be briefly stated as follows: The carbonate and sulphate of potash react with the carbon, nitrogen, and iron, forming in the first instance sulphide of potassium, which afterwards converts the iron into sulphide, whilst potassium cyanide is simultaneously produced. It should be here explained that ferrocyanide of potassium (yellow prussiate) is not formed during the ignition of the above mentioned materials, but results from the lixiviation of the fused mass with water, when the cyanide of potassium and iron sulphide decompose each other, producing ferrocyanide and sulphide of potassium. It is quite obvious that even if any ferrocyanide were produced during the process of fusion, it would almost immediately be decomposed, at the intense heat to which the mass is subjected, into potassium cyanide, iron carbide, and nitrogen gas. If any doubt were felt on this point, the experiments of Liebig conclusively prove that the formation of ferrocyanide takes place on dissolving the ignited mass in water, but not previously. Liebig found that if the fused mixture be allowed to cool, and then treated with moderately strong alcohol, potassium cyanide alone is extracted, and the residue when dissolved in water no longer yields ferrocyanide. As ferrocyanide is not formed during the process of fusion, the presence of iron in the preliminary stages may appear superfluous; but such is not the case. The presence of iron is necessary for two reasons, firstly, because the sulphate of potash which is generally present is converted into sulphide and bisulphide, and these, in the absence of iron, would decompose some of the cyanide of potash into sulphocyanate, thereby causing a loss of cyanogen so far as yellow prussiate is concerned; and secondly, because potassium bisulphide has a very corrosive action on the iron pot in which the fusion takes place. When iron is present it readily decomposes any alkaline sulphides, thereby preventing formation of sulphocyanate, and being itself converted into iron sulphide, which is again changed into prussiate by the action of the aqueous cyanide.

Pear-shaped iron pots were formerly used for fusing the raw materials. The arrangement now generally adopted in large English works consists of a series of iron pots almost hemispherical in shape, set in brickwork, and each heated by a separate fire and circular flue. These vessels are closed by iron lids, with apertures for the admittance of animal matters, the aperture being at once closed by a slide after each addition. Through every lid there passes a vertical spindle, carrying a set of blades for mixing the materials, and set in motion by a suitable shaft worked by steam power. Instead of the ordinary iron pots, reverberatory furnaces are often employed, especially in Germany. The reason for this preference is, that ordinary iron vessels are worn out in a comparatively short time, the destructive action being greatest on the under surface of the muffle. A much larger quantity of raw material can also be operated upon at one time if a reverberatory furnace be used. The mode of procedure depends to some extent upon the condition of the organic materials employed. If fresh, the muffle or furnace must be left open, so as to permit the mixture to be well and frequently stirred, and additions to be made at intervals until eventually ammonia ceases to be evolved. The furnaces are arranged in such a manner that when the carbonate of potash has once become fused the doors of the fire-place may be shut, and no fresh firing is required during the introduction of the animal matters. The molten mass is kept well stirred by means of a thick iron bar, suspended by a chain, and fixed in an aperture in the side of the furnace. By the use of this arrangement the stirring is much more easily and thoroughly effected than is the case with the old fashioned pots. Ordinary reverberatory furnaces cannot be used for the fusion, because the silica in the hearth would combine with the potash to form silicate of potash. Gas generators with air blast are now sometimes employed instead of ordinary fuel in the manufacture of yellow prussiate of potash. Several advantages are gained by operating in this manner, especially that of permitting the regulation of temperature and the admission of oxygen, so as to obtain an ordinary, a neutral, or a reducing flame, according to requirements. In the preparation of the “metal,” for every 100 parts of pearlash from 100 to 125 parts of fresh animal substances are required, together with 6 or 8 parts of iron in some form or other. The pearlash, or a mixture of 1 part of pearlash with 2 to 4 parts “blue salt” or “blue potash” (this substance will be referred to later on), is melted in the furnace and heated to bright redness, so that the temperature of the mass may not be reduced too much by the addition of the animal matters. These, in their original condition, or an equivalent quantity of carbonised materials, together with the proper proportion of iron, are then introduced—first pretty frequently, afterwards at longer intervals. Each addition of animal matter causes a somewhat violent frothing and escape of combustible gases, along with water and carbonic acid, and the whole becomes thick—not so much owing to the introduction of solid substances as by the fall of temperature, resulting from the production of such large quantities of gas. In order to hasten the decomposition, vigorous stirring must be applied. When the reaction is at an end, the semi-fluid mass is transferred to cast-iron dishes, and the furnace is again filled with carbonate of potash and heated. In this way four or five charges may be accomplished every day, and the process carried on continuously. The most favourable conditions for effecting the melting part of the process are attained when the heat approaches whiteness, and a bright, clear flame is produced as soon as the raw materials are introduced. According to one authority, woollen rags and good pearlash, with a small proportion of waste iron, have produced the largest yield of yellow prussiate, although even in this case two-thirds of the total nitrogen present was lost in the form of ammonia.

(2) Lixiviation.—The fused mass, if properly prepared, should yield about 16 per cent. of prussiate on dissolving in water. In this part of the process, the “metal” when cold is broken into lumps and placed in cold water mixed with the weak lyes from former operations. Heat is then applied until the temperature rises to about 180°-190° F., and the liquid is stirred vigorously so as to promote rapid solution, because some of the potassium cyanide is apt to be decomposed during lixiviation. When the solution attains a density of 30°-40° Tw. it is left to clarify, the heat being withdrawn. The clear solution is decanted, and evaporated in pans, which are generally heated by the waste heat of the furnaces. When it has a density of 54° Tw. it is run off into the crystallisers, where it deposits the crude salt.

(3) Crystallisation.—This is a very important stage of the manufacture, as it is the final process by which the crude prussiate is rendered sufficiently pure to be placed on the market. The impure substance is dissolved in warm water until the solution stands at 54° Tw.; after all insoluble matter has deposited, the clear liquor is placed in the crystallising vessels. These are occasionally made of wood; but when such vessels are used, the crystallised salt generally possesses a green colour, which is believed to be due to the tannin present in the wood. On this account cast-iron crystallisers are more frequently employed. The crystallisation proceeds slowly—often going on for several weeks in large vessels. The mother liquor is then drawn off, and if not too impure is used for dissolving fresh quantities of the crude prussiate. The ferrocyanide is deposited in crusts in the crystallisers; but by hanging lumps of the solid salt in the solution, long clusters of crystals may be obtained, and by suspending these in fresh prussiate lyes immense crystals are produced. From 100 parts crude prussiate about 90 parts pure potassium ferrocyanide are obtained, or sometimes in the case of purer materials 97 parts.

Sulphate of potash is often present in commercial yellow prussiate. The separation of this impurity is best effected on the large scale by evaporating the prussiate solution to a density of 62° Tw., at which point most of the sulphate will crystallise out. If the clear liquor be then drawn off, diluted to 52° Tw., and allowed to cool, almost pure potassium ferrocyanide will gradually deposit. This may be rendered absolutely pure by gently fusing the crystals, dissolving in water, and treating with a small quantity of acetic acid, which will decompose any carbonates and cyanides. On adding sufficient strong alcohol, the ferrocyanide is precipitated, and when crystallised once or twice more from water it may be regarded as chemically pure.

Blue salt.—This substance, to which we have previously referred, is a residue obtained in the manufacture of prussiate of potash. The last mother-liquor contains a large quantity of carbonate of potash, along with smaller amounts of hydrate, silicate, chloride, and sulphocyanate. It is concentrated until the liquid has a density of 90° Tw., when most of the chloride, silicate, &c., separates out, and the strong liquor containing the greater proportion of the carbonate is evaporated to dryness, and calcined in a reverberatory furnace. The dry residue constitutes the “blue salt” or “blue potash,” and contains from 70 to 80 per cent. carbonate of potash. It may be employed instead of pearlash, or mixed with it, for the next batch of yellow prussiate. The composition and amount of the insoluble residue left on lixiviation of the “metal” vary according to the proportions and character of the raw materials used. Other conditions being equal, horn gives the lowest percentage of insoluble matter on lixiviation.

The large proportions of potash and phosphates contained in the insoluble residues render them well suited for use in the manufacture of artificial manures. As already mentioned, when regarded from a scientific or economical point of view, the yellow prussiate industry is carried on under very imperfect conditions. In addition to the amount of potash, there is a very considerable waste of nitrogen, firstly, because the larger proportion of that element present in the animal substances is not converted into cyanogen at all, but passes off chiefly in the form of ammonia salts; and, secondly, because part of the potassium cyanide which is actually produced is lost by decomposition, and another portion is left in the mother liquor. It has been calculated that out of every 100 parts of ferrocyanide which should theoretically be obtained, 4 parts are lost when fairly pure materials have been employed, and 14 in the case of impure ingredients.

The following analyses indicate the percentage composition of two samples of insoluble residue:—

No. 1...No. 2.
Sulphate of potash, &c.9·06..3·21
Phosphates of lime, magnesia and iron13·74..6·24
Oxide of iron13·34..19·58
Lime and magnesia5·08..7·23
Sand and silica23·97..29·24
Charcoal and moisture34·81..34·50
100·00..100·00