Garment cutting in the twentieth century

by Günther F. Hertzer

The front edge of a vest must also be explained, although the different diagrams cannot fail to make the correct impression. In Dia. [XIII], it will be noticed that in the front of the neck a small gore has been cut, which will bring the straight front line to the oval shape of the body. On a frock coat the larger gore toward the waist effects the same thing. On a vest the under arm cut is made where the gore in the frock coat is cut, and consequently the vest has that gore balanced in the side seam. A vest cut close up to the neck and without collar would not look well to have a gore cut in front of the neck, and so the deduction is made in front by starting the front-edge about 3¼ numbers from the point of 135 deg., and on the plumb line, and meeting the front line again at line 9. On a double-breasted vest, which is intended to button all the way up to the neck, and lap over to the other side, this gore must be cut, not where it is marked in Dia. [XIII], but in a cut forming the lapel, and which cut should be as large as the gore shown in Dia. [II]. It is impossible to make a double-breasted garment of any kind without that large gore if it is intended to fit the form when buttoned over. It is true, very few vests of that kind are made; but that kind of a cut must be made in all double-breasted garments if a well-fitting front is to be obtained when buttoned up.

From line 9 to line 15 the front line is the front edge of a single-breasted vest, receding a trifle at the lower button. Very few vests are cut all the way up to the neck, and consequently the gore at the neck, as in Dia. [XIII], is entirely cut away and of no account. Single-breasted vests that button up, say to about 2 in. above line 9, can be fitted without any gore; but the front edge should be worked so that it will not stretch out in making, particularly around the open neck. Low-cut vests, and without turn-down collars, must be fairly well drawn in at the open neck, or the long opening will gape more or less. Single-breasted as well as double-breasted vests with a low opening should have half an inch gore cut under the collar. The gap may be taken away by drawing the neck in with a thread or stay; but a gore is better—the maker should know just what to do with it. Stretching the collar will never do any good—it will give the collar a different shape, but will never bring a gaping front to the body.

In producing a double-breasted vest, 1 to 1½ in. may be added to the front edge, and the buttons set back that much from the place where they would be if the vest were single-breasted. To obtain the proper balance for the bottom of the double-breasted vest along the buttons, so that both sides meet, sweep from 3¾ at the plumb base line on Dia. [IV] through the bottom of the front part of the angle of 15 deg., or as far backward as the buttons will be located. This is a sure sweep. (See Dia. [IV].)

Besides the gore under the collar, or the drawing in of the edge around the neck of a double-breasted vest, I have found in a majority of cases that it is well to lengthen the back, say ½ inch—which gives the front a better opportunity to settle in its place. It is ten times better to have the back of a vest a trifle too long than too short. The difference between a vest and a coat may well be observed from Dia. [I], [II] and [IV]. It is useless to describe them, and I will conclude this article with the following remarks:

A coat must fit best behind and at the shoulders, for the front can be regulated by moving the buttons, and for this reason a center line in front is not important; but it is very handy to have one for a system, whenever you want a straight front.

A vest is intended to fit best in front, and for this reason the front is cut loose at the front of the waist. The vest is cut off a few inches below the waist, and a trifle loose cloth will not show; but if a coat were cut as loose there the skirt below would flare in all directions. To regulate the top button of a coat and vest, so that the coat will cover the vest when buttoned, place the top button-hole, say on line 9 for the coat, and ½ in. lower for the vest. The single-breasted coat has one inch more cloth there, and the button may be set back one inch on the coat, and on the vest as near as the button-holes when buttoned. The coat will cover the vest about one inch, and this may be used as a guide whenever the opening of the coat and vest are lowered.

To the center of the front also belongs the lapel, and a cutter should know just how much to use for that purpose, and with that object in view examine the front of a clergyman’s coat as shown in Dia. [I]. A coat of this kind is, of course, without turnover or lapel, but it must be loose, though not too wide; and if it is correct that the angle of 135 deg. makes the top of the front just large enough to sew it up with a seam, providing a large gore is cut below at the waist, then it follows that the buttons and front of the button-holes must be sewed one seam back of that line, and enough cloth left in front of the base as is required in front of the button-holes and in front of the buttons. If the edge is bound half an inch on the button-hole side and one inch on the button side it will answer very well; but if the edge is turned in one more seam must be allowed. The space in front of the button-holes should not be less than five-eighths inches and may be three-fourths, and the button side may have one-half an inch more for extra lap.

Now, I will refer to Dia. [III] and [XII]. Observe the circle which is drawn from 60 degs. on the right and through 135 degs., which circle gives as good a top to the lapel as anything that can be contrived, and the whole front produces an extreme cut-away. If the lapel is to be run further down, all we find necessary to do is to allow on the bottom of the lapel, say three-fourths inches, and shape the upper part according to notion. If we desire a long roll of the lapel, a gore should be cut under the lapel, and the gore and seam again allowed in front, so that the original width of the circle and on top of the lapels, is not destroyed. There is no question but that a larger lapel requires a trifle more width around the second or third button-hole, but how much must always depend upon the notions of the cutter; but in all cases the lapel of a single-breasted coat should be large enough to allow the second or third button-hole, or all, to be made without coming in the break of the roll, and a neat lapel need never be larger than for that purpose, no matter how low it is to roll. It is here where the touches of a fancy cutter can be seen, and a cutter has always a chance to become more proficient on that point. Even with the greatest care he may often obtain a lapel that does not suit him. But the cutter alone can not do all. The journeyman must have the taste and the ability to make it so that it will not only suit the cutter, but will also be admired by the public.

If the front of Dia. [I] was to be sewed together with a seam like the back, the front line of the angle of 135 degs. would have to be cut through, and that would fit down to between lines 15 and 17½, but below that point the front would have to be reduced 15 degs., and at the same time where the front requires reduction, the back requires an addition, all of which is shown in Dia. [I].

There is one more important point to be considered in connection with the center of front and back, and this is the length. For particular forms, or for odd forms, it may be measured as follows: From the top of back measure straight down behind, and again, from the top of back measure forward, striking point 11¼ on the plumb base line, as near as you can, and from that point go straight down to a level bottom for both back and front. To obtain that level bottom by the scale, make both back and front even long from the point of the angle of 135 degs. for a frock coat, after all seams are sewed.