| A | Main Driving Pulley, 16 in. dia. x 4-1/4 in. face; 5-1/4 in. face for Two-beater Machine. |
| A1 | Beater Driving Pulley, 30 in. dia. x 4-1/4 in. face. |
| B | Beater Pulley, 9 in. dia. x 4-1/4 face (occasionally 10 in. dia.) |
| B1 | Feed Pulley, 3 in. to 13 in. dia. x 2-1/4 in. face; advancing by 1/2 in. increments. |
| B2 | Calender Section Fan Driving Pulley, 6 in. dia.x 2-1/4 in. face. |
| B3 | Calender Fan Pulley, 8 in. dia. x 2-1/4 in. face. |
| B4 | Cage Section Fan Driving Pulley, 6 in. dia. x2-1/4 face for Straight Machine or direct connected Opener and BreakerLapper. If with Trunking Connection, B4 is 8 in. dia. and B5 is 6 in.dia., to give higher speed of Fan. |
| B5 | Cage Fan Pulley, 8 in. dia. x 2-1/4 in. facefor Straight Machine or direct connected Opener and Breaker Lapper. Ifwith Trunking Connection, B4 is 8 in. dia. andB5 is 6 in. dia., to give higher speed of Fan. |
| C | Driving Pulley for Bottom Cross Shaft, etc., 18 in. dia. x 2-1/4 in. face. |
| C1 | Clutch Driving Gear, 15 T. |
| D | Large Clutch Gear, 35 T. |
| D1 | Small Clutch Gear, or Bottom Shaft Driving Gear, 17 T. |
| E | Bottom Cross Shaft Driven Gear, 96 T. |
| E1 | Front Lap Calender Roll Driving Gear, 12 T. |
| E2 | Bottom Cross Shaft Gear, driving Calender Rolls and Top Cross Shaft, 14 T. |
| F | Large Double Intermediate, driving Top Cross Shaft, 50 T. |
| F1 | Small Double Intermediate, driving Bottom Calender Roll, 27 T. |
| F2 | Bottom Calender Roll, 7 in. dia. |
| G | Top Cross Shaft Gear, 30 T. |
| G1 | Side Shaft Driving Bevel Gear, 24 T. |
| H | Side Shaft Bevel Gear, Calender End, 24 T. |
| H1 | Side Shaft Bevel Gear, Feed End, 28 T. |
| I | Compound Intermediate Bevel Gear, 28 T. |
| I1 | Compound Intermediate Gear, driving Bottom Feed Roll, 37 T. |
| J | Bottom Feed Roll, 2 in. dia. |
| [{42}] | |
| J1 | Bottom Feed Roll Gear, 33 T. |
| J2 | Cage Section Top Stripping Roll Driving Gear, 9 T.; 8 T. Gear may be used to vary speed. |
| K | Cage Section Top Stripping Roll Intermediate Gear, 52 T. |
| L | Cage Section Top Stripping Roll Gear, 14 T. |
| M | Cage Section Bottom Stripping Roll Gear, 14 T. |
| M1 | Cage Section Bottom Cage Driving Gear, 23 T. |
| N | Cage Section Bottom Cage Intermediate Gear, 20 T. |
| O | Cage Section Bottom Cage Gear, 181 T. |
| O1 | Cage Section Top Cage Gear, 181 T. |
| P | Front Lap Calender Roll, 9 in. dia. |
| P1 | Front Lap Calender Roll Gear, 53 T. |
| P2 | Back Lap Calender Roll Driving Gear, 24 T. |
| Q | Back Lap Calender Roll Intermediate Gear, 22 T. |
| R | Back Lap Calender Roll Gear, 24 T. |
| R1 | Back Lap Calender Roll, 9 in. dia. |
| S | 3d Calender Roll Gear, 21 T. |
| S1 | 3d Calender Roll, 5-1/2 in. dia. |
| T | 2d Calender Roll Gear, 22 T. |
| T1 | 2d Calender Roll, 5-1/2 in. dia. |
| U | Top Calender Roll Gear, 23 T. |
| U1 | Top Calender Roll, 5-1/2 in. dia. |
| V | Calender Section Top Stripping Roll Intermediate Gear, 17 T. |
| V1 | Calender Section Top Stripping Roll Intermediate Gear, 17 T. |
| W | Calender Section Top Stripping Roll Gear, 14 T. |
| X | Calender Section Bottom Stripping Roll Gear, 14 T. |
| X1 | Calender Section Bottom Cage Driving Gear, 23 T. |
| Y | Calender Section Bottom Cage Intermediate Gear, 20 T. |
| Z | Calender Section Bottom Cage Gear, 181 T. |
| Z1 | Calender Section Top Cage Gear, 181 T. |
BREAKER LAPPERS.
DRAFT CALCULATIONS.
INTERMEDIATE OR FINISHER LAPPER.
SIDE VIEW OF GEARING
