Practical Hand Book of Gas, Oil and Steam Engines / Stationary, Marine, Traction; Gas Burners, Oil Burners, Etc.; Farm, Traction, Automobile, Locomotive; A simple, practical and comprehensive book on the construction, operation and repair of all kinds of engines. Dealing with the various parts in detail and the various types of engines and also the use of different kinds of fuel.

by John B. Rathbun

(b) Descending a little farther, the top of the piston uncovers the opening of the transfer port B, allowing the compressed gases in the crank case to enter the cylinder as shown by the arrows. These gases, guided by the deflector plate on the top of the piston are thrown upwardly, as shown by the arrows, and sweep the residual burnt gases before them through the exhaust port. The cylinder is now filled with the combustible mixture ready for compression.

STROKE 2. The piston now moves up on the compression stroke, compressing the charge in the cylinder and at the same time creates a vacuum in the crank-case. Just before the piston reaches the end of the exhaust stroke, the lower edge of the piston uncovers the inlet port A (See Fig. 7), which allows the mixture from the carburetor to flow into the partial vacuum and fill the crank case ready for the next initial compression. When the end of the stroke is reached, the charge in the combustion chamber C is fired and the cycle is repeated. It should be noted that the incoming gas and the initial compression are controlled entirely by the action of the lower edge of the piston on the inlet port A.

(28) Reversing Two Cycle Motors.

As the admission and exhaust in the two stroke cycle engine each occur once per revolution, and are controlled directly by the piston position at opposite ends of the stroke, it is evident that the direction of rotation is not affected by gas control or valve timing, as in the case of the four stroke cycle engine. The factor that does determine the direction of rotation in the two stroke engine is the time at which ignition occurs in regard to the angular position of the crank. By changing the relation between the crank position at the end of the compression stroke and the time at which the spark occurs, it is possible to reverse the engine even when it is running.

Should the engine be standing still in the position shown by Fig. 6, with the crank on the dead center, when ignition occurred, there would be no more tendency to turn the crank to the right than to the left, providing of course, that there was no effect from the momentum of a revolving fly wheel. If ignition occurred with the crank inclined ever so little toward the right, the pressure of the piston would force the crank downwards in a right handed direction. If the crank were inclined to the left, the tendency would be for left handed rotation.

If the ignition system were arranged so that the spark occurred when the crank was inclined towards the right every time that the piston came up on the compression stroke, we should have continuous rotation in a right hand direction. By shifting the sequence of the spark so that it occurred with the crank on the left we would cause the engine to stop and reverse to left handed rotation. This is exactly the method used in reversing two stroke motors in practice, the change in the ignition being accomplished by advancing or retarding the mechanism that dispatches the spark (“Timer” or “Commutator”).

Fig. F-9. Cross Section of Fairbanks-Morse Three Port—Two Stroke Cycle Engine, with Parts Named.

This is an advantage not possessed by the four stroke cycle engine of the ordinary type, as the cams and valve mechanism require reversal as well as a reversal of the ignition system. This relation between the valve action and rotation in a four stroke cycle engine may be illustrated by the following example. Consider the piston at the end of the compression stroke in an engine designed for right hand rotation. After ignition, under the proper conditions, the piston would descend turning the crank to the right until it reached the bottom of the stroke, at which point the exhaust valve would open and relieve the pressure in the cylinder.

Let us now consider an attempt at reversing the engine by causing the spark to occur before the piston reached the end of the compression stroke with the crank still inclined toward the left. In this case the piston would force the crank down in a left hand direction until it reached the end of the stroke. The exhaust valve would not open to relieve the pressure, as the exhaust cam would be moving away from the valve rod instead of toward it. Should the crank swing a little past the dead center, because of its momentum, the inlet valve would be opened instead of the exhaust, and the contents of the cylinder would shoot through the intake pipe and carburetor. This would bring matters to a close as far as rotation was concerned.