The simple cut-out ([Fig. 8]) is constructed in the same manner as the simple switch, except that there are two points of contact instead of one. This is the principle of the telephone and telegraph instrument wiring, so that a bell or sounder may be rung from a distance. The arm is then thrown over and the bell cut out, allowing the “phone” or key to be brought into use. In lifting the transmitter from the hook on a telephone, a cut-out is operated and the bell circuit is thrown out of action. It is in operation again directly the transmitter is returned to the hook. The switch cut-out ([Fig. 9]) is inactive when the arm is in the position shown in the illustration; but when it is thrown over (as shown by the dotted line) it connects the poles at opposite ends of the board. It may be thrown over in both directions, and is a useful switch for many purposes.
For strong currents the lever-switch, that rests on a brass tack-head, will not be suitable, as the switch-bar must be held firmly in place to make a perfect connection. Strong currents throw weak switches open, causing an open or broken circuit.
A single pole-switch, to carry a current up to one hundred and twenty-five volts and twenty-five amperes, is shown in [Fig. 10]. This consists of a base-block, a bar which is attached to the vertical ears of a binding-post, and a clutch that will hold the bar when it is pressed down between the ears.
The base-block should be made from some non-conducting material, such as soapstone, marble, or slate. If a piece of soapstone can be procured, that will be just the thing, since it is easily worked into the proper shape and size. Soapstone may be sawed and smoothed with a file; it is easily bored into with a gimlet-bit, and it is one of the best non-conducting substances. The base for this switch is six inches long, two inches wide, and as thick as the soapstone happens to be—say three-quarters of an inch. The top edge may be bevelled for the sake of appearance or left square.
Two pieces of heavy sheet copper or brass are to be cut as shown at A in [Fig. 11]. The ears are half an inch wide, and the total height of the strip is two inches and a half, while the part with two holes in it side by side is one inch and a quarter long, including the half-inch width of the vertical strip. With round and flat-nosed pliers bend the long ears into shape, so as to form a keeper for the bar which is then to be riveted in place. Omit the holes at the ends of the long ears in the other plate; then bend it into shape to form a clutch that will hold the bar when it is pressed down between the ears. These binding-posts should be made fast to the base-block with brass machine-screws and nuts, which will fit in countersunk holes in the bottom of the soapstone. If hard-wood is used for the base, ordinary brass wood-screws will answer very well.
The connection-bar is cut from metal the same thickness as that employed for the binding-posts and clutches; it should be shaped so as to appear as shown at B in [Fig. 11]. A handle should be driven on the slim end, and where the lower edge enters between the ears of the clutch, the corners of the bar should be rounded with a file. Countersunk screw-holes are bored in the base, so that it can be made fast to the wood-work.
A double pole-switch is shown in [Fig. 12], and in general construction it is similar to the single pole-switch described above. The binding posts and bars are cut and bent from the patterns A and B in [Fig. 11]; but in this case the long, slim ends of the bars are omitted. A short turn is made at the handle end of each bar and a hard-wood block is placed between the bar-ends and held in position with screws driven through holes made in the bars and into the ends of the block. A handle is made fast to the middle of the block with a long and slim wood-screw; or a steel-wire nail may be passed through the handle and block, a burr slipped over the end opposite the head, and the small end riveted fast. When the binding-posts (to which the ends of the bars are attached) are screwed onto the base, be sure and see that the bars are parallel and the same distance apart at both ends. In like manner, when the cleat binding-posts are made fast, see that they are directly in line with the bars, so that the yoke will drop into the spaces between the ears without having to be pulled to one side or the other. This is a very useful switch for strong currents, and may be placed close to a dynamo, so that the current in both wires may be cut out at once.