(18) Sea Island Cotton. This is the finest class of cotton produced, being long in the staple, very flexible, and having very regular convolutions. If care be taken in ginning, so that the fibre is not broken, the finest yarns can be produced from this variety. The length of Sea Island Cotton is stated by Dr. Bowman to reach 2·20 inches in the case of Florida grown, but Mr. Monie states the average length to be 1·8 inches. Mr. Evan Leigh confirms the higher length, but only in the case of cotton grown on the Edisto Island. Varieties of this grade are grown in Peru, Fiji, and Australia, the average lengths being respectively 1·56, 1·87, 1·65 inches. Fijian Sea Island is spoiled by bad ginning, which breaks the fibres very much. The colour of Sea Island cotton is a light creamy one, and is peculiar to it.
(19) Egyptian Cotton. Egyptian cotton varies considerably in colour, length, and quality. The variety known as Gallini is of a golden colour, the fibres being tough and strong, and the convolutions very regular. It has a mean length of 1·5 inch. Brown Egyptian is, as its name implies, of that colour, and like Gallini, the fibres are strong and tough, but are coarser, the convolutions are less regular, and the wall of the fibre is also denser. The mean length is 1·4 inch and the diameter 1⁄1325 inch. White Egyptian is, perhaps, the most valuable of all this class of cotton when properly treated. It is of a light gold colour, the fibres being strong and pliable, but only partially spiral. As a result of this, the yarn spun is greater in diameter than that spun from Gallini (weights being equal), the fibres not lying so closely together. This cotton mixes well with American and Brazilian.
(20) Brazilian and Peruvian Cotton. Pernambuco cotton is of a slightly golden colour, and is, comparatively speaking, hard and wiry, being thus well adapted for twist yarn. The twists in the fibre are well developed, and the average length is 1·25 inch. Maranham is of a dull gold colour, mixing well with American cotton. There are several other varieties of Brazilian cotton, which need not be further referred to. Rough Peruvian cotton is very clean, of a creamy colour, and is possessed of an average strength. The fibres are only irregularly twisted, and an average length is 1·3 inch. The smooth variety is fairly regularly convoluted, and mixes well with Orleans.
(21) American. There are several varieties of American cotton, which are grown in the Southern States. Taking them in their order as regards length of staple, the first to notice is Orleans. The better classes of this are very uniform in length, clean and light in colour, often being pure white. One feature of Orleans cotton which renders it very acceptable to spinners, is that it is very flexible, and possessed of a high elasticity. In addition to this, as has been previously noted, its strength is fairly great, and generally its spiral form is well developed. The average length is about 1 inch. Texas cotton is less pliable than Orleans, darker in colour, and is not put on the market so free from immature fibre. Its diameter is greater, and its average length about equal to Orleans. Upland cotton is clean, and little waste is produced from it. The fibres are well suited for weft yarns, being soft and elastic, and of a very light colour. Spun without any admixture of other cotton, yarns as high as 425’s can be produced, but when mixed with Egyptian or some other strong fibre, higher counts can be obtained. Mobile is similar in colour to Orleans, and is equal to Uplands in strength. It is not so good as either of these for manufacturing purposes, being much dirtier, and having more flattened fibres in it.
(22) Indian. The whole of the cottons grown in India are less valuable than the preceding varieties, owing to the facts that they are not so regularly spiral, and that the staple is more variable. The highest class is Hingunghat, which is more convolute than any other Indian grown cotton. The fibres vary in diameter, but have an average length of 1·03 inch. Broach is brownish gold in colour and is fairly clean, although it is not thoroughly cleaned, and contains a good deal of leaf and nep. It is about 0·9 inch long, and is more regular in this respect than Hingunghat. The spirals are fewer in number, and it is stated by Mr. Monie that the walls are very liable to rupture. Dhollerah is of a white colour, and is best adapted for weft yarn. Oomrawuttee is creamy in colour, being strong but rather short in the staple. A good deal of impurity is found in this quality, but the convolute form is moderately developed. Tinnivelly is grown in the Madras Presidency, and is a fairly good cotton. In strength it is high and is very elastic, its colour being a dull, creamy one. The fibres have a small bore and thick walls, and are, in addition, only slightly twisted. The worst Indian fibre is Bengal, which is short, strong, and dirty.
(23) Commercial qualities. The recapitulation of the principal features of various growths of cotton just given enables their relative value for spinning to be pointed out, and at the same time to indicate the qualities it is desirable to retain during the subsequent mechanical treatment. Sea Island cotton is beyond doubt the finest quality existing, and, in the manufacture of fine counts, is absolutely essential. Its general excellence is undoubtedly attributable to the conditions under which it is grown, and even this might be improved by more careful cultivation. Egyptian cotton is also of great value in the production of good yarns, and is very largely used for this purpose. Owing to the existence of a number of short fibres, always found in commercial quantities, but present here in larger proportion, it is necessary to comb all Egyptian cotton. The chief advantage of its use is that being relatively stronger, smoother surfaced, and more flexible than qualities other than Sea Island, a large range of yarns for various uses can be spun at a price which enables them to be profitably used. The fibres are very regular in diameter, and when twisted lie very close together. The most widely used cotton is, however, the various brands of American, which have the advantage of careful attention during their growth and collection. In consequence of this, there is a very high uniformity attained, together with great freedom from all sorts of impurities, these two qualities rendering American cotton highly suited for general use. Indian cotton is coarser, harsher, and not so clean as other varieties, and requires greater care in its manufacture. Summing up, the desirable points in cotton are the length and regular convolute form of the fibre, together with its freedom from mechanical and chemical impurities. The object of the earlier mechanical processes through which cotton passes is to remove all the impurities, lay the fibres regularly and in equal numbers alongside each other, without breaking or rupturing them, and without destroying their natural tendency to twist round each other. In doing this, not merely do the seeds, leaf, and sand require removal, but also the short immature fibres which form into little knots or tangles called “neps.” Great care is needed in the preparatory stages so as to avoid damage, and it is especially necessary to avoid the removal of the waxy sheath which plays an important part in the manufacture of the fibre. The necessity for a warm, humid atmosphere has already been referred to, but it may be noted that it is very important on account of its softening effect upon the waxy sheath. If the latter be removed the heat becomes a source of difficulty instead of a help, as the natural moisture existing in the fibre is more speedily absorbed.
CHAPTER III.
GINNING AND MIXING MACHINES.
(24) When the cotton is ready for harvesting it is picked from the shrubs by hand. There have been many attempts to pick it by machinery, but these have not hitherto been very successful. After picking, it is subjected to the action of a machine called a “gin,” which is sometimes arranged to be worked by hand, but more often by power. In the latter case the machines are placed in a shed, and the cotton is brought there for treatment. The object of ginning is to remove from the cotton the seeds, which adhere closely to the fibre, and which have of late years acquired considerable value for oil-producing purposes. In order to remove them it is necessary that the fibre should be held in some way while it is submitted to a rubbing or scraping action, by which the seed is separated. To effectually perform this function great care is required, as otherwise a quantity of the seed is broken, and the fibres are rubbed up into “neps.” If either of these effects is produced additional labour is thrown on the spinner in his subsequent treatment, and it is therefore desirable to avoid such a manipulation of the machine as would lead to so undesirable a result.
(25) In Figs. [1] and [2] a single Macarthy gin is illustrated in part sectional side elevation and front elevation. This is a type which, in principle, is now largely adopted. It consists of a roller A, rotated in the direction shown by the arrow, by means of a strap passing over a pulley fixed on the end of the roller shaft. The latter is square, and is passed through the centre of the roller, fitting a corresponding hole in the latter, and being carried by suitable bearings fixed on the machine frame. In constructing the roller A the following method is adopted. Wood segments are fitted together so as to form the complete cylinder, or the latter may be made in one piece. Having produced the body, it is fixed on the shaft, and is then turned quite round and parallel. Upon the surface so prepared a thick covering of walrus leather B is fixed, in which spiral grooves are formed. The rough surface of the leather, as the roller is revolving, seizes the cotton fibres as they are fed along the table F, which has a grid G at its inner end, a special feed being sometimes fitted. When the fibres are drawn in by the roller they are taken under a knife blade C, which is fixed above the roller by means of the sets of clamps D and E. The clamps D bind the blade to its bearings, and those marked E are used to regulate its pressure on the roller A. As the roller occasionally becomes hollow the wisdom of this procedure will be seen. A crank shaft is placed and driven from the shaft of the roller, and gives a rapid reciprocating motion to a connecting rod I, which has at its upper end a blade H. The height of the blade H is regulated by means of the adjustment of the connecting rod strap, to which it is jointed, and which can be packed to any desired amount. The blade is coupled to radius arms J, adjustable by nuts at their outer ends, and oscillating on a rod fixed below the feed-table.