Practical Education, Volume II

by Maria Edgeworth; Richard Lovell Edgeworth

"No."

"Would a feather, if it were moving with the greatest conceivable swiftness or velocity, throw down a castle?"

"No."[21]

"Would a mountain torn up by the roots, as fabled in Milton, if it moved with the least conceivable velocity, throw down a castle?"

"Yes, I think it would."

The difference between an uniform, and an uniformly accelerated motion, the measure of the velocity of falling bodies, the composition of motions communicated to the same body in different directions at the same time, and the cause of the curvilinear track of projectiles, seem, at first, intricate subjects, and above the capacity of boys of ten or twelve years old; but by short and well-timed lessons, they may be explained without confounding or fatiguing their attention. We tried another experiment whilst this chapter was writing, to determine whether we had asserted too much upon this subject. After a conversation between two boys upon the descent of bodies towards the earth, and upon the measure of the increasing velocity with which they fall, they were desired, with a view to ascertain whether they understood what was said, to invent a machine which should show the difference between an uniform and an accelerated velocity, and in particular to show, by occular demonstration, "that if one body moves in a given time through a given space, with an uniform motion, and if another body moves through the same space in the same time with an uniformly accelerated motion, the uniform motion of the one will be equal to half the accelerated motion of the other." The eldest boy, H——, thirteen years old, invented and executed the following machine for this purpose:

Plate I, Fig. 3. b is a bracket 9 inches by 5, consisting of a back and two sides of hard wood: two inches from the back two slits are made in the sides of the bracket half an inch deep, and an eighth of an inch wide, to receive the two wire pivots of a roller; which roller is composed of a cylinder, three inches long and half an inch diameter; and a cone three inches long and one inch diameter in its largest part or base. The cylinder and cone are not separate, but are turned out of one piece; a string is fastened to the cone at its base a, with a bullet or any other small weight at the other end of it; and another string and weight are fastened to the cylinder at c; the pivot p of wire is bent into the form of a handle; if the handle is turned either way, the strings will be respectively wound up upon the cone and cylinder; their lengths should now be adjusted, so that when the string on the cone is wound up as far as the cone will permit, the two weights may be at an equal distance from the bottom of the bracket, which bottom we suppose to be parallel with the pivots; the bracket should now be fastened against a wall, at such a height as to let the weights lightly touch the floor when the strings are unwound: silk or bobbin is a proper kind of string for this purpose, as it is woven or plaited, and therefore is not liable to twist. When the strings are wound up to their greatest heights, if the handle be suddenly let go, both the weights will begin to fall at the same moment; but the weight 1, will descend at first but slowly, and will pass through but small space compared with the weight 2. As they descend further, No. 2 still continues to get before No. 1; but after some time, No. 1 begins to overtake No. 2, and at last they come to the ground together. If this machine is required to show exactly the space that a falling body would describe in given times, the cone and cylinder must have grooves cut spirally upon their circumference, to direct the string with precision. To describe these spiral lines, became a new subject of inquiry. The young mechanics were again eager to exert their powers of invention; the eldest invented a machine upon the same principle as that which is used by the best workmen for cutting clock fusees; and it is described in Berthoud. The youngest invented the engine delineated, Plate 1, Fig. 4.

The roller or cone (or both together) which it is required to cut spirally, must be furnished with a handle, and a toothed wheel w, which turns a smaller wheel or pinion w. This pinion carries with it a screw s, which draws forward the puppet p, in which the graver of chisel g slides without shake. This graver has a point or edge shaped properly to form the spiral groove, with a shoulder to regulate the depth of the groove. The iron rod r, which is firmly fastened in the puppet, slides through mortices at mm, and guides the puppet in a straight line.