Speed regulation is effected by varying the number of nozzles in flow, that is, for light loads fewer nozzles are open and a smaller volume of steam is admitted to the turbine wheel, but the steam that is admitted impinges against the moving blades with the same velocity always, no matter whether the volume be large or small. With a full load and all the nozzle sections in flow, the steam passes to the wheel in a broad belt and steady flow.

Depth
inches 		⅛¼⅜½⅝¾⅞
0  .00 .01 .05 .09 .14 .19 .26 .32
1  .40 .47 .55 .64 .73 .82 .92 1.02
2  1.13 1.23 1.35 1.36 1.58 1.70 1.82 1.95
3  2.07 2.21 2.34 2.48 2.61 2.76 2.90 3.05
4  3.20 3.35 3.50 3.66 3.81 3.97 4.14 4.30
5  4.47 4.64 4.81 4.98 5.15 5.33 5.51 5.69
6  5.87 6.06 6.25 6.44 6.62 6.82 7.01 7.21
7  7.40 7.60 7.80 8.01 8.21 8.42 8.63 8.83
8  9.05 9.26 9.47 9.69 9.91 10.13 10.35 10.57
9  10.80 11.02 11.25 11.48 11.71 11.94 12.17 12.41
10  12.64 12.88 13.12 13.36 13.60 13.85 14.09 14.34
11  14.59 14.84 15.09 15.34 15.59 15.85 16.11 16.36
12  16.62 16.88 17.15 17.41 17.67 17.94 18.21 18.47
13  18.74 19.01 19.29 19.56 19.84 20.11 20.39 20.67
14  20.95 21.23 21.51 21.80 22.08 22.37 22.65 22.94
15  23.23 23.52 23.82 24.11 24.40 24.70 25.00 25.30
16  25.60 25.90 26.20 26.50 26.80 27.11 27.42 27.72
17  28.03 28.34 28.65 28.97 29.28 29.59 29.91 30.22
18  30.54 30.86 31.18 31.50 31.82 32.15 32.47 32.80
19  33.12 33.45 33.78 34.11 34.44 34.77 35.10 35.44
20  35.77 36.11 36.45 36.78 37.12 37.46 37.80 38.15

NOTE.—The weir table on this page contains figures 1, 2, 3, etc., in the first vertical column which indicates the inches depth of water running over weir board notches. Frequently the depths measured represent also fractional inches, between 1 and 2, 2 and 3, etc. The horizontal line of fraction at the top represents these fractional parts, and can be applied between any of the numbers of inches depth, from 1 to 25. The body of the table shows the cubic feet, and the fractional parts of a cubic foot, which will pass each minute for each inch in depth, and for each fractional part of an inch by eighths for all depths from 1 to 25 inches. Each of these results is for only one inch width of weir. To estimate for any width of weir the result obtained for one inch width must be multiplied by the number of inches constituting the whole horizontal length of weir.

Figs. 2,760 and 2,761.—Samson vertical runner and shaft, and complete Samson vertical turbine. The runner is composed of two separate and distinct types of wheel, having thereby also two diameters. Each wheel or set of buckets receives its separate quantity of water from one and the same set of guides, but each set acts only once and singly upon the water used, and the water does not act twice upon the combined wheel, as some suppose. In construction, the lower or main set of buckets is made of flanged plate steel, and cast solidly into a heavy ring surrounding the outer and lower edges, and into a heavy diaphragm, separating the two sets of buckets.