| Arbor Press (complete with following 12 parts) | 27115 |
| Main Casting | 27114 |
| Latch | 27107 |
| Bed Plate | 27113 |
| Lever | 27108 |
| Rack | 27211 |
| Washer | 27112 |
| Pinion Shaft | 27110 |
| Pinion | 27109 |
| Latch Pin | 27111 |
| *Special CLN & KPN Spacer | 27233 |
| *Special CLN & KPN Latch | 27232 |
| *Special CLN & KPN Bed Plate | 27234 |
| Large Peening Tool (9-21 RHN, WHN, BHN, SHC, KPN, CLN; 11-17 JFN) | 27101 |
| Small Peening Tool (7-WHN, RHN, SHC; 9-JFN) | 27100 |
| Peening Tool for small terminal posts in which are east threaded brass inserts (Columbia) | 27105 |
| Large Post Freeing Tool | 27103 |
| Small Post Freeing Tool | 27102 |
| No. 8 Post Freeing Tool (13/16" diameter straight post) | 27123 |
| 1 Large Post Re-Builder (9-21 RHN, WHN, BHN, SHC, KPN, CLN; 11-17 JFN) | 27005 |
| 1 Small Post Re-Builder (7-WHN, RHN, SHC; 9-JFN) | 27004 |
| 2 Ford Positive Post Builder | 27006 |
| 2 Ford Negative Post Builder | 27224 |
| 2 No. 8 Post Builder (13/16" diameter straight post) | 27225 |
| Style "B" Prest-O-Lite Torch, with six feet of red gum tubing | A-3116 |
| Automatic Reducing Valve | A-427 |
| COMPLETE TYPE "N" OUTFIT including all parts above | 27116 |
* The CLN and KPN Spacer block, bent Latch and Bed Plate are special parts used only in the Arbor Press when it is especially assembled to lock CLN or KPN posts.
1 The Re-Builder is used to build up posts before attempting to lock on the cover. The replacing of the metal cut away from the original diameter of the post when the jar cover was removed is necessary to the correct operation of the Peening Tool.
2 The Builder is used to build up posts, after they have been locked and shaped by the Peening Tool, to a size large enough to take some special terminal. For example, the Ford Positive Post Builder is used in building up posts, locked by the Large Peening Tool, to the proper size to take the Ford positive terminal.
The Automatic Reducing Valve delivers the gas from the P-O-L tank at a uniform pressure of 3 pounds per square inch, whether the tank is full, half empty, or nearly empty, and regardless of the volume of gas used. The volume or flow of gas is regulated by the key.
The style "B" torch mixes the pure acetylene from the gas tank with the proper amount of air necessary to an efficient heating flame.
The heating flame is conducted or delivered to the Peening Tool by the short length of brass tubing known as the Torch-Holder, over which the "B" Torch is pressed by hand in completing the assembly.
Both the "B" Torch and the Automatic Reducing Valve are absolutely essential to the use of the Prest-O-Lite gas tank for heating the Peening Tool.
Prest-O-Lite gas tanks, style A, B, C, or E, may be used in connection with the Automatic Reducing Valve, as shown in Fig. 248. To use a welding size gas tank it is necessary to insert a "W to A" Adapter between the tank and Reducing Valve. This Adapter can be purchased from the Prest-O-Lite Co., Inc.