The superior results which the hollow-top burner was calculated to afford did not become fully apparent until the burner was made of non-conducting material, and greater care exercised in its construction. This appears to have been done in Germany earlier than in this country. But, in England, it was undoubtedly Mr. Sugg who first turned his attention to the improvement of the burner, and demonstrated its merits. Mr. Sugg commenced the manufacture of this burner in steatite in the year 1868; and since that time the burner has been extensively employed, and its advantages widely recognized. The superiority of hollow-top burners produced by Mr. Sugg to those previously manufactured, is chiefly the result of their being made in steatite instead of in metal. With this material, greater exactness and uniformity are obtained in the shape and dimensions of the burner than when metal is employed; besides which there is (what has been before referred to) the advantage arising from its inferior conductive capacity for heat, and its non-liability to corrosion. Another Sugg's hollow-top burner. improvement, also due to Mr. Sugg, and which is productive of noticeable results, consists in cutting the slit of the burner with a circular saw, applied from above, so as to make the ends of the slit curved instead of horizontal; by which means the tendency of the gas to issue laterally at the ends of the slit, and form horns to the flame, is lessened. Mr. Sugg's table-top burner (which was introduced in 1880), in addition to the characteristic features of the hollow-top, has a rim-like projection from the burner, below the slit; its object being to protect the flame from the disturbing influence of the uprush of air in its immediate vicinity, and so preserve its shape unaltered, while diminishing its liability to smoke. Prior to Mr. Sugg—namely, in the early part of 1879—Mr. Bray had successfully obviated this injurious action upon the flame of the ascending current of air, by affixing to the burner two arms of brass, so placed as to be immediately under the projecting wings of the flame.
1868 Burner. —1874 Burner. —Table-Top Burner.
Fig. 10.—Sugg's Hollow-Top Burners.
BRAY'S BURNERS.
The burners of Messrs. George Bray and Co. have deservedly acquired a world-wide reputation, and are in extensive use wherever gas lighting is known. Their distinguishing characteristic, and that which has won for them the high repute in which they are held, is the union of cheapness with remarkable efficiency. In all the various descriptions and classes of burners which are produced by this firm, the characteristic referred to is preserved; although it is needless to add that the different varieties are not equally efficient. Of the three forms of flat-flame burners we have been considering—batswing, union-jet, and hollow-top—the one which, more than any other, has been the speciality of the firm is the union-jet; and it is with the development of this class of burner that the name of Bray is most intimately and honourably associated.
Union-Jet. —Hollow-Top or Slit-Union.[ [9] —Batswing.
Fig. 11.—Bray's "Regulator" Burners.
Bray's "regulator" burner. The "regulator" union-jet, which was the first notable burner produced by Messrs. Bray, has received, perhaps, a wider application than any other single gas-burner. It consists of a cylindrical brass case, screwed at one end for insertion into the fittings, and at the other containing a tip of "enamel"—a material invented by Mr. Bray, and apparently of somewhat similar composition to the "adamas" of Mr. Leoni—the "enamel" tip being perforated, in the usual manner, with two holes, set at an angle to each other, for the outflow of the gas. The distinctive feature of this burner is the introduction into the lower part of the brass case of a layer, or layers, of muslin; designed to check in some degree, and to steady the current or flow of the gas through the burner. At the time of its introduction, this burner compared very favourably, as regards the results it yielded, with other burners in common use; and its fairly good performances, Bray's "special" burner. together with the very low price at which it can be sold, cause it still to be extensively employed wherever the attainment, from the gas consumed, of the highest obtainable results may be subordinated to cheapness, or in situations where, from delicacy of construction or from the care and attention demanded, a more efficient burner may not be so suitable. But in the matter of developing the illuminating power of the gas employed, the "regulator" is far surpassed by the more recently introduced "special" burner of the same makers.
