Hunting with the Bow & Arrow

by Saxton T. Pope

I have one like a shoemaker's last, made of two pieces of wood separated by a thin slat which can be removed, permitting easy withdrawal of the quiver after drying. When dry, your quiver will be about twenty-two inches deep, four inches across the top, and slightly conical. Cut a strip of deer hide eight inches long by one and a half wide, shave it, double the hair side in, and attach it to the seamy side of the quiver by perforating the leather and inserting a lacing of buckskin thongs. Leave the loop of this strap projecting two inches above the top of the quiver. In the bottom of your quiver drop a round piece of felt or carpet to prevent the arrow points coming through the hide.

If you are not so fortunate as to have deer hide, you may use any stiff leather, or even canvas. This latter can be made stiff by painting or varnishing it.

Such a receptacle will hold a dozen broad-heads very comfortably and several more under pressure. It should swing from a belt at the right hip in such a way that in walking it does not touch the leg, while in shooting it is accessible to the right hand or may then be shifted slightly to the front for convenience.

In running we usually grasp the quiver in the right hand, not only to prevent it interfering with locomotion, but to keep the arrows from rattling and falling out. When on the trail of an animal we habitually stuff a twig of leaves, a bunch of ferns or a bit of grass in the mouth of the quiver to damp the soft rustling of the arrows. Sometimes, in going through brush or when running, we carry the quiver on a belt slung over the left shoulder. Here they are out of the way and give the legs full action.

To keep the arrows dry, and to cover them while traveling, we make a sheath for the quiver of waterproof muslin. This is long enough to cover the arrows and has a wire ring a bit larger than the top of the quiver sewn in the cloth some three inches from the upper end. This keeps the feathers from being crushed. The mouth of this cover is closed with a drawstring. On the side adjacent to the strap of the quiver, an aperture is cut to permit this being brought through and fastened to the belt.

The bow itself has a long narrow case made of the same cloth, or canvas, or green baize with a drawstring at the top and a leather tip at the bottom. Where several bows are packed together, each has a woolen bow case and all are carried in a canvas bag, composition carrying cylinder, or in a wooden bow box. In hunting we prefer the canvas bag, but you must carry it yourself, any one else will break your bows.

The bracer, or arm guard, is a cuff of leather worn on the left forearm to prevent the stroke of the bowstring doing damage. Some archers can shoot without this protection, but others, because of their style of shooting or their anatomical formation, need it. It can be made like a butcher's cuff, some six or eight inches long, partially surrounding the forearm and fastened by three little straps or by lacing in the back. Another form is simply a strip of thin sole leather from two to three inches wide by eight long, having little straps and buckles attached to hold it in position on the flexor surface of the wrist and forearm.

The bracer not only keeps the arm from injury, but makes for a clean release of the arrow. Anything such as a coat sleeve touching the bowstring when in action, diverts the arrow in its flight. On the sleeve of your shooting jersey you can sew a piece of leather for an arm guard.

While one may pick up a bow and shoot a few shots without a glove or finger protection, he soon will be compelled to cease because of soreness. Doubtless the ancient yeoman, a horny-handed son of toil, needed no glove. But we know that even in those days a tab of leather was held in the hand to prevent the string from hurting. The glove probably is of more modern use and quite in favor among target archers. We have found it rather hot in hunting, so have resorted to leather finger tips. These are best made of pigskin or cordovan leather, which is horse hide. This should be about a sixteenth of an inch thick and cut to such a form that the tips enclose the finger on the palmar surface up to the second joint and leave an oval opening over the knuckle and upper part of the finger nail. The best way to make them is to mould a piece of paper about each of the first three fingers on the right hand, gathering the paper on the back and crimping it with the thumb nail to show where to cut the pattern. Lay the paper out flat and cut it approximately according to the illustrated form.