In Newfoundland there was very fine birch but no cedar. There was, however, excellent spruce which would take the place of cedar. It seems certain, then, that all the framework of the Beothuk canoes was of spruce. It seems likely that they were never built of a single sheet of birch but were covered with a number of sheets sewn together, as in other early Indian birch-bark canoes. The canoe birch of Newfoundland grew to a diameter of 2 to 2½ feet at the butt, which would produce a sheet of birch of 6 to 7 feet width; the length would be decided by how far up the tree the Indian could climb to make the upper cut. As has been stated, the prehistoric Indians seemingly made little attempt to build birch-bark canoes of long lengths of bark, preferring to use only the bark obtainable near the ground and above the height of the winter snows.
The form of the Beothuk canoes, particularly the lack of bilge and the marked V-form, has caused much speculation. One writer assumed that the form was particularly suited for running rapids. Actually, the Beothuk appeared to have used canoes for river travel very rarely, as few rivers in their country were suited for navigation. Instead, they seem to have been coast dwellers and to have used canoes for coastal travel and for voyages from island to island.
Their canoes were undoubtedly designed for open-water navigation, and the V-form was particularly suitable for this. The draft aided in keeping the canoe on its course with either broadside or quartering winds, and if the Beothuks knew sail, the hull-form would have served them well. It is quite evident that the Beothuk canoes used ballast in the form of stones or heavy cargo. Stones would have been placed along the keel piece and covered with moss and skins. The strongly hogged sheer was useful in protecting cargo amidships from spray and, in picking up a seal or porpoise, the canoe could be sharply heeled without taking in water. The V sections fore and aft were suitable for rough-water navigation; because of its form and the weight of ballast, the canoe would pass partly over and through the wave-top without pounding. If a wave of such height as to overtop the gunwales just abaft the stem were met, the strongly flaring sides would give reserve buoyancy, causing the canoe to lift quickly as the wave reached up the sides.
The small sticks in the ends, mentioned by John Gay, served not only for lifting the canoe but also as braces to support the canoe at a given angle when turned over ashore to serve as a shelter. The Beothuk canoe, because of its form, was not well suited for portaging, and it must be concluded that little of this was done. In coastal voyages, the canoe would be unloaded and brought ashore each night to serve as a shelter.
It is believed that the gunwale lashing of these canoes was in groups, as in the Malecite. Howley questioned an old Micmac who had seen the Beothuk lashing; he likened it to the continuous lashing used by his own people, indicating some form of group wrapping, at least. It is probable that the group lashings were let into the gunwales by shallow notching at each group, a common Indian practice when no rail cap was used, to prevent abrasion from the paddle or from loading and unloading the canoe. The lacing of the ends appears to have been in the common spiral stitch, judging by the grave models. These, however, show a continuous wrapping at the gunwales, a common simplification found in Indian canoe models, representing either group or continuously wrapped gunwales indiscriminately.
The paddle of the Beothuks had a long, narrow blade, probably with a pointed tip and a ridged surface. The shape is nearly spatulate. The handle is missing from the grave model but was perhaps of the usual "hoe-handled" form without a top cross-grip.
From these descriptions and on the basis of common Indian techniques in birch-bark canoe construction, the form and methods of building the Beothuk canoe can be reconstructed. The drawing on page [97] shows the probable shape and appearance of the finished canoe. It seems likely that a level building bed was first prepared. The keel, probably rectangular in cross section, was then formed of two poles placed butt-to-butt, worked to shape, and scarfed. The fastening of the scarf was probably two or more lashings let into the surface of the wood. These lashings are assumed to have been of split-root material but may have been sinew. Possibly to strengthen the scarfs, pegs were also used, a technique consistent with the state of Beothuk culture. The keel probably had its ends split into laminae to allow the sharp bend required to form the bow and stern pieces; and it was probably treated with hot water and staked out to the desired profile. The main gunwales were similarly made and worked to the predetermined sheer which, in staking out, was hogged to a greater degree than was required in the finished canoe. The ends of the gunwales were apparently split into laminae to allow the shaping of the sharp upsweep of the sheer close to bow and stern. The outwales were probably formed in the same manner, after which the three thwarts were made and the material for ribs and sheathing prepared. The ribs were apparently bent to the desired shape, using hot water, and were either staked out or tied to hold them in form until needed.
Figure 87
Beothuk Canoe, Approximate Form and Construction