The Building of a Book / A Series of Practical Articles Written by Experts in the Various Departments of Book Making and Distributing

by Unknown

THE PRINTING PRESS
By Otto L. Raabe

Throughout the stages of development of the book-printing press the chief object has been to lessen the cost of printing. Whether the direct purpose of an improvement has been to increase the working speed of the press, to lessen the necessary operating power, to simplify the mechanism, to strengthen the parts, to lighten the pressman's labor, or to better the quality of printing, the ultimate aim has always been the same. It has been the constant incentive to invention and the standard for judging the adaptability of a press.

The first printing press was the "wooden screw" press, which came into use about the middle of the fifteenth century, and was built upon the same mechanical principle as the linen presses in the homes of the well-to-do. This was the press used by Gutenberg.

It consisted of two upright timbers held together at the top and the bottom by crosspieces of wood and with two intermediate cross-timbers. One of these intermediate cross-timbers supported a wooden or stone "bed" on which the form of type was placed, and through the other passed a large wooden screw, the lower point of which was attached to the centre of a flat, wooden plate, called the "platen." The lower side of the platen was covered with a soft "packing" or "blanket" of cloth. After the type had been inked, a sheet of paper was laid on it. This paper had previously been dampened so that it would take a better impression of the type. The screw was then turned down until the platen pressed the paper against the inked type, and produced a printed sheet.

The form of type was incased in a frame called a "coffin." These coffins and the type within them were very heavy, but they had to be lifted in and out of the press by hand. After each impression the platen was screwed upward so that the sheet of paper which had been printed could be removed and hung up to dry.

This simple form of press continued in use without material change until the early part of the seventeenth century. The first improvements on it came about 1620, and consisted of a device for rolling in and out the wooden or stone bed on which the type rested instead of lifting it by hand, of a new form of iron hand-lever for turning the screw, and of an iron screw in place of the wooden one. These were the inventions of William Janson Blaeuw, a printer of Amsterdam. Blaeuw's press was introduced into England and used there as well as on the continent. It was substantially the same press as that on which Benjamin Franklin worked when in London in 1735.

After this first type of printing press had been in use for three and a half centuries, a much-improved form was invented by the Earl of Stanhope in 1798. The frame of his press was made of iron, cast in one piece; the bed, the impression plate, or "platen," and the other large parts were also of cast iron, while the working parts were of iron, steel, or brass. The iron impression screw was retained, but connected to it was a combination of levers whereby its power was greatly increased. This enabled the printing of larger forms and the use of a thinner and harder "packing," or "tympan," between the platen and the sheet of paper to be printed, resulting in a sharper and clearer impression. Much less exertion was required to work the lever, and at first, on this account, a printer, who was accustomed to use all his physical force on the old screw press, found it difficult to work on the new one.

This improved style of press was received with so much favor by printers that several persons took up its manufacture, and competition soon reduced its cost and brought it into general use for printing newspapers as well as books. The process of printing remained about the same as in the earlier presses. Two men were required to work it. One spread the ink on a wooden block, rolling over it with two leather-covered balls, about six inches in diameter, stuffed with wool or horsehair, and fastened to round wooden handles. Holding one of these inking balls in each hand, he then rolled one upon the other to distribute the ink evenly over both of them, and applied the ink to the face of the type by rocking the balls over it until the entire form was inked. While this was being done, the other man was placing the sheet of paper on the "tympan." This was a light frame, in two parts, really forming two frames, one inside the other, and both covered with parchment. There was a woollen or felt blanket between them, and the two frames were held together by hooks. The outer frame was hinged at its lower end to the outer end of the bed of the press, and when ready to receive the paper, it stood in a nearly upright position at about right angles to the bed. On the frame were two or four pins, upon which the sheet of paper was impaled.

Attached to the upper end of the inner frame by hinges was a thin and narrow frame, called the "frisket," of the same length and width as the inner tympan frame. This frisket was covered with strong paper in which were openings, cut a little larger than the size of the pages of the type-form. When the sheets of paper had been placed upon the tympan frame, the frisket was folded down upon it, and the two were then turned down over the form of type. The bed was then "run in" under the platen by means of a crank at the side of the press, and the platen was screwed down to make the impression. After the impression had been taken, the platen was screwed up, the bed "run out," the tympan frame and frisket lifted, and the printed sheet taken off.

The introduction of this Stanhope press gave a great impetus to the development of the printing press in other countries as well as in England, and many varieties were devised during the thirty years following. Although as early as 1811 Koenig had made a cylinder press which had proved fairly successful, the better grades of printing could be obtained only by the flat pressure of the hand-presses. In some of these hand presses, the platen, or upper impression plate, was moved into position over the bed and remained stationary while the bed with the type-form upon it was forced upward to make the impression. In others, the platen was hinged to the bed, but in all of them the mechanism was complicated.