Various types of furnaces and apparatus have from time to time been designed, and the subject has been one of much experiment and many failures. The principal towns in Types of destructors. England which took the lead in the adoption of the refuse destructor system were Manchester, Birmingham, Leeds, Heckmondwike, Warrington, Blackburn, Bradford, Bury, Bolton, Hull, Nottingham, Salford, Ealing and London. Ordinary furnaces, built mostly by dust contractors, began to come into use in London and in the north of England in the second half of the 19th century, but they were not scientifically adapted to the purpose, and necessitated the admixture of coal or other fuel with the refuse to ensure its cremation. The Manchester corporation erected a furnace of this description about the year 1873, and Messrs Mead & Co. made an unsatisfactory attempt in 1870 to burn house refuse in closed furnaces at Paddington. In 1876 Alfred Fryer erected his destructor at Manchester, and several other towns adopted this furnace shortly afterwards. Other furnaces were from time to time brought before the public, among which may be mentioned those of Pearce and Lupton, Pickard, Healey, Thwaite, Young, Wilkinson, Burton, Hardie, Jacobs and Odgen. In addition to these the “Beehive” and the “Nelson” destructors became well known. The former was introduced by Stafford and Pearson of Burnley, and one was erected in 1884 in the parish yard at Richmond, Surrey, but the results being unsatisfactory, it was closed during the following year. The “Nelson” furnace, patented in 1885 by Messrs Richmond and Birtwistle, was erected at Nelson-in-Marsden, Lancashire, but being very costly in working was abandoned. The principal types of destructors now in use are those of Fryer, Whiley, Horsfall, Warner, Meldrum, Beaman and Deas, Heenan and Froude, and the “Sterling” destructor erected by Messrs Hughes and Stirling.
| Fig. 1.—Fryer’s Destructor. |
The general arrangement of the destructor patented[1] by Alfred Fryer in 1876 is illustrated in fig. 1. An installation upon this principle consists of a number of furnaces or cells, usually Fryer’s. arranged in pairs back to back, and enclosed in a rectangular block of brickwork having a flat top, upon which the house refuse is tipped from the carts.
| Fig. 2.—Horsfall’s Improved Destructor. |
A large main flue, which also forms the dust chamber, is placed underneath the furnace hearths. The Fryer furnace ordinarily burns from 4 to 6 tons of refuse per cell per 24 hours. It will be observed that the outlets for the products of combustion are placed at the back near the refuse feed opening, an arrangement which is imperfect in design, inasmuch as while a charge of refuse is burning upon the furnace bars the charge which is to follow lies on the dead hearth near the outlet flue. Here it undergoes drying and partial decomposition, giving off offensive empyreumatic vapours which pass into the flue without being exposed to sufficient heat to render them entirely inoffensive. The serious nuisances thus produced in some instances led to the introduction of a second furnace, or “cremator,” patented by C. Jones of Ealing in 1885, which was placed in the main flue leading to the chimney-shaft, for the purpose of resolving the organic matters present in the vapour, but the greatly increased cost of burning due to this device led to its abandonment in many cases. This type of cell was largely used during the early period of the history of destructors, but has to a considerable extent given place to furnaces of more modern design.
| Fig. 3. - Meldrum’s Destructor at Darwen |
A furnace[2] patented in 1891 by Mr Henry Whiley, superintendent of the scavenging department of the Manchester corporation, is automatic in its action and was designed primarily with a Whiley’s. view to saving labour—the cells being fed, stoked and clinkered automatically. There is no drying hearth, and the refuse carts tip direct into a shoot or hopper at the back which conducts the material directly on to movable eccentric grate bars. These automatically traverse the material forward into the furnace, and finally push it against a flap-door which opens and allows it to fall out. This apparatus is adapted for dealing with screened rather than unscreened refuse, since it suffers from the objection that the motion of the bars tends to allow fine particles to drop through unburnt. Some difficulty has been experienced from the refuse sticking in the hopper, and exception may also be taken to the continual flapping of the door when the clinker passes out, as cold air is thereby admitted into the furnace. As in the Fryer cell, the outlet for the products of combustion into the main flue is close to the point where the crude refuse is fed into the furnace, and the escape of unburnt vapours is thus facilitated. Forced draught is applied by means of a Roots blower. The Manchester corporation has 28 cells of this type in use, and the approximate amount of refuse burnt per cell per 24 hours is from 6 to 8 tons at a cost per ton for labour of 3.47 pence.
Horsfall’s destructor[3] (fig. 2) is a high-temperature furnace of modern type which has been adopted largely in Great Britain and on the continent of Europe. In it some of the general features Horsfall’s. of the Fryer cell are retained, but the details differ considerably from those of the furnaces already described. Important points in the design are the arrangement of the flues and flue outlets for the products of combustion, and the introduction of a blast duct through which air is forced into a closed ash-pit. The feeding-hole is situated at the back of and above the furnace, while the flue opening for the emission of the gaseous products is placed at the front of the furnace over the dead plate; thus the gases distilled from the raw refuse are caused to pass on their way to the main flue over the hottest part of the furnace and through the flue opening in the red-hot reverberatory arch. The steam jet, which plays an important part in the Horsfall furnace, forces air into the closed ash-pit at a pressure of about ¾ to 1 in. of water, and in this way a temperature varying from 1500° to 2000° F., as tested by a thermo-electric pyrometer, is maintained in the main flue. In a battery of cells the gases from each are delivered into one main flue, so that a uniform temperature is maintained therein sufficiently high to prevent noxious vapours from reaching the chimney. The cells being charged and clinkered in rotation, when the fire in one is green, in the others it is at its hottest, and the products of combustion do not reach the boiler surfaces until after they have been mixed in the main flue. The cast iron boxes which are provided at the sides of the furnaces, and through which the blast air is conveyed on its way to the grate, prevent the adhesion of clinker to the side walls of the cells, and very materially preserve the brickwork, which otherwise becomes damaged by the tools used to remove the clinker. The wide clinkering doors are suspended by counterbalance weights and open vertically. The rate of working of these cells varies from 8 tons per cell per 24 hours at Oldham to 10 tons per cell at Bradford, where the furnaces are of a later type. The cost of labour in stoking and clinkering is about 6d. per ton of the refuse treated at Bradford, and 9d. per ton at Oldham, where the rate of wages is higher. Well-constructed and properly-worked plants of this type should give rise to no nuisance, and may be located in populous neighbourhoods without danger to the public health or comfort. Installations were put down at Fulham (1901), Hammerton Street, Bradford (1900), West Hartlepool (1904), and other places, and the surplus power generated is employed in the production of electric energy.
Warner’s destructor,[4] known as the “Perfectus,” is, in general arrangement, similar to Fryer’s, but differs in being provided with special charging hoppers, dampers in flues, dust-catching Warner’s. arrangements, rocking grate bars and other improvements. The refuse is tipped into feeding-hoppers, consisting of rectangular cast iron boxes over which plates are placed to prevent the escape of smoke and fumes. At the lower portion of the feeding-hopper is a flap-door working on an axis and controlled by an iron lever from the tipping platform. When refuse is to be fed into the furnace the lever is thrown over, the contents of the hopper drop on to the sloping firebrick hearth beneath, and the door is at once closed again. The door should be kept open as short a time as possible in order to prevent the admission of cold air into the furnace at the back end, since this leads to the lowering of the temperature of the cells and main flue, and also to paper and other light refuse being carried into the flues and chimney. The flues of each furnace are provided with dampers, which are closed during the process of clinkering in order to keep up the heat. The cells are each 5 ft. wide and 11 ft. deep, the rearmost portion consisting of a firebrick drying hearth, and the front of rocking grate bars upon which the combustion takes place. The crown of each cell is formed of a reverberatory firebrick arch having openings for the emission of the products of combustion. The flap dampers which are fitted to these openings are operated by horizontal spindles passing through the brickwork to the front of the cell, where they are provided with levers or handles; thus each cell can be worked independently of the others. With the view of increasing the steam-raising capabilities of the furnace, forced draught is sometimes applied and a tubular boiler is placed close to the cells. The amount of refuse consumed varies from 5 tons to 8 tons per cell per 24 hours. At Hornsey, where 12 cells of this type are in use, the cost of labour for burning the refuse is 9½d. per ton.
The Meldurm “Simplex” destructor (fig. 3), a type of furnace which yields good steam-raising results, is in successful operation at Rochdale, Hereford, Darwen, Nelson, Plumstead and Meldrum’s. Woolwich, at each of which towns the production of steam is an important consideration. Cells have also been laid down at Burton, Hunstanton, Blackburn and Shipley, and more recently at Burnley, Cleckheaton, Lancaster, Nelson, Sheerness and Weymouth. In general arrangement the destructor differs considerably from those previously described. The grates are placed side by side without separation except by dead plates, but, in order to localize the forced draught, the ash-pit is divided into parts corresponding with the different grate areas. Each ash-pit is closed airtight by a cast iron plate, and is provided with an air-tight door for removing the fine ash. Two patent Meldrum steam-jet blowers are provided for each furnace, supplying any required pressure of blast up to 6 in. water column, though that usually employed does not exceed 1½ in. The furnaces are designed for hand-feeding from the front, but hopper-feeding can be applied if desirable. The products of combustion either pass away from the back of each fire-grate into a common flue leading to boilers and the chimney-shaft, or are conveyed sideways over the various grates and a common fire-bridge to the boilers or chimney. The heat in the gases, after passing the boilers, is still further utilized to heat the air supplied to the furnaces, the gases being passed through an air heater or continuous regenerator consisting of a number of cast iron pipes from which the air is delivered through the Meldrum “blowers” at a temperature of about 300° F. That a high percentage (15 to 18%) of CO2 is obtained in the furnaces proves a small excess of free oxygen, and no doubt explains the high fuel efficiency obtained by this type of destructor. High-pressure boilers of ample capacity are provided for the accumulation during periods of light load of a reserve of steam, the storage being obtained by utilizing the difference between the highest and lowest water-levels and the difference between the maximum and working steam-pressure. Patent locking fire-bars, to prevent lifting when clinkering, are used in the furnace and have a good life. At Rochdale the Meldrum furnaces consume from 53 ℔ to 66 ℔ of refuse per square foot of grate area per hour, as compared with 22.4 ℔ per square foot in a low-temperature destructor burning 6 tons per cell per 24 hours with a grate area of 25 sq. ft. The evaporative efficiency of the Rochdale furnaces varies from 1.39 ℔ to 1.87 ℔ of water (actual) per 1 ℔ of refuse burned, and an average steam-pressure of about 114 ℔ per square inch is maintained. The cost of labour and supervision amounts to 10d. per ton of refuse dealt with. A Lancashire boiler (22 ft. by 6 ft. 6 in.) at the Sewage Outfall Works, Hereford, evaporates with refuse fuel 2980 ℔ of water per hour, equal to 149 indicated horse-power. About 54 ℔ of refuse are burnt per square foot of grate area per hour with an evaporation of 1.82 ℔ of water per pound of refuse.