Milling was formerly all done in milling or fulling stocks (see Fig. 5), in which the cloth saturated with a strong solution of soap (with or without other additions such as stale urine, potash, fuller’s earth, &c.) is subjected to the action of heavy wooden hammers, which are raised by the cams attached to the wheel (E) on the revolving shaft, and fall with their own weight on to the bundles of cloth. The shape of the hammer-head causes the cloth to turn slowly in the cavity in which the milling takes place. Occasionally, the cloth is taken out, straightened, washed if necessary, and then returned to the stocks to undergo further treatment, the process being continued until the material is uniformly shrunk or milled to the desired degree.
In the more modern forms of milling machines the principle adopted is to draw the pieces in rope form, saturated with soap solution and sewn together end to end so as to form an endless band, between two or more rollers, on leaving which they are forced down a closed trough ending in an aperture the size of which can be varied, but which in any case is sufficiently small to cause a certain amount of force to be necessary to push the pieces through. A machine of this kind is shown in Fig. 6. It is evident that for coloured goods which have to be milled only such colouring matters must be chosen for dyeing that are absolutely fast to soap.
| From Ganswindt, Technologie der Appretur. |
| Fig. 6.—Roller Milling Machine. |
After the pieces have been milled down to the desired degree, they present an uneven and, undesirable appearance on the surface, the ends of many of the fibres which previously projected having been turned and thus become embedded in the body of the cloth. In order to bring these hairs to the surface again, the fabric is subjected to teasing or raising, an operation identical in principle with one which has already been noticed under the finishing of cotton. In place of the steel wire brushes it is the usual practice to employ teasels for the treatment of woollen goods.
The teasel (see Fig. 7) is the dried head (fruit) of a kind of thistle (Dipsacus fullorum), the horny sharp spikes of which turn downwards at their extremity, and, while possessing the necessary sharpness and strength for raising the fibres, are not sufficiently rigid to cause any material damage to the cloth. For raising, the teasels are fixed in rows on a large revolving drum, and the piece to be treated is drawn lengthways underneath the drum, being guided by rollers or rods so as to just touch the teasels as they sweep past. In the raising of woollen goods it is necessary that the pieces should be damp or moist while undergoing this treatment.
After teasing, the pieces are stretched and dried. At this stage they still have an irregular appearance, for although the raising has brought all the loose ends of the fibres to the surface, these vary considerably in length and thus give rise to an uneven nap.
| From Ganswindt, Technologie der Appretur. |
| Fig. 7.—Teasel used for Raising. |
By the next operation of shearing or cropping, the long hairs are cut off arid a uniform surface is thus obtained. Shearing was in former times done by hand, by means of shears, but is to-day universally effected by means of a cutting device which works on the same principle as an ordinary lawn-mower, in which a number of spiral blades set on the surface of a rapidly revolving roller pass continuously over a straight fixed blade underneath, the roller being set so that the spiral blades just touch the fixed blade. Before the piece comes to the shearing device the nap is raised by means of a rotary brush. Shearing may be effected either transversely, in which case the fixed blade is parallel to the warp, or longitudinally with the fixed blade parallel to the weft. In the first case, the piece being stretched on a table, over which the cutter, carried on rails, travels from selvedge to selvedge. The length of the piece that can be shorn in one operation will naturally depend upon the length of the blade, but in any case the process is necessarily intermittent, many operations being required before the whole piece is shorn. In the longitudinal shearing machines the process is continuous, the pieces passing from the beam in the stretched condition over the rotary brush, under the fixed blade, and then being again brushed before being beamed on the other side of the machine. Shearing once is generally insufficient, and for this reason many of the modern machines are constructed with duplicate arrangements so as to effect the shearing twice in the same operation. In the finishing of certain woollen goods the pieces, after having been milled, raised and sheared, go through these operations again in the same sequence.
After these operations the goods are pressed either in the hydraulic press or in the continuous press, and according to the character of the material and the finish desired may or may not be steamed under pressure, all of which operations are described below.
New cloth, as it comes into the hands of the tailor, frequently shows an undesirable gloss or sheen, which is removed before making up by a process known as shrinking, in which the material is simply damped or steamed.