The key locks chiefly used in English safes have been the ordinary lever lock with 6-8 or 10 levers, Chubb’s “detector,” Hobbs’s “protector” or variants of these. In the Yale lock, which reverts in some degree to the idea of the ancient Egyptian Key locks. lock, America has produced one key lock which has come into almost universal use in that country and is certainly worthy of note. The key of this lock, shown full size at ka in fig. 12, is remarkably small, being stamped from a piece of flat steel and weighing only a small fraction of an ounce. The barrel abc has to turn, as in the Bramah lock, in order to move the bolt, which is not shown in the figure. That may be done either as in Bramah locks or by a tongue or bit attached to the end ab of the barrel as in several other locks. The barrel is prevented from being turned, except by the proper key, thus. The (apparently) five plugs with spiral springs over them in fig. 12 are really all divided at the cross line bc, being all now lifted to the proper height by the key. Consequently the barrel abc can turn round, as there is no plug either projecting from it or projecting into it. But when the key is out, all the plugs are pushed down by the springs, and so the upper ones descend into the barrel and hold it fast. And again, if any of the steps of a false key are too high, some of the lower plugs will be pushed up beyond the barrel into the holes above them, and so the barrel cannot turn. The bevelled end of the key near a enables it to be pushed in under the plugs, though with some friction and resistance.
It is frequently convenient to have a number of different locks so arranged that, whilst each has its own individual key, yet one special or “master” key will operate any of the series. In warded locks this is done by “differing” the wards of the individual locks so that each key will only pass its own lock, and then filing away the bit of an extra key so that it will pass all the wards; the objection to this method is that any of the individual keys can easily be filed away and so form a master key. A better method, which meets this objection, consists in making all the levers except one—or if need be two—of each lock alike and cutting another gating or widening the gating in the differing levers, so as to pass the master key which has one—or two—special steps.
The growth of safe deposits has called for special locks so that when a box changes tenants the outgoing tenant’s key shall be useless. In some cases the lock has been taken off and another substituted, but this is a clumsy makeshift now rarely employed, and has been superseded by the use of changeable key locks.
| Fig. 13. |
The first of these, invented by Robert Newell in 1841, was introduced into Great Britain from America by Hobbs in 1851. A simpler form, the construction of which is clearly shown by fig. 13, was brought out by Hobbs, Hart & Co. The bolt of this lock, instead of the ordinary main stump, carries a set of sliders, PPS, one corresponding to each lever and each carrying a projection S corresponding to a portion of the main stump. It will be seen that if any key having steps of certain lengths is inserted when the lock is unlocked and the bolt B thrown thereby, each slider will be raised to a height corresponding to that to which its lever is raised by the key, and the two fixed teeth CC will engage two of the teeth in the front of each slider, so that they will be held in place ready to enter the lever gatings when the same key is inserted.
| Fig. 14. |
A changeable key lock introduced by the Chatwood Safe Co. has no gatings in the levers, whose fronts are cut with teeth gearing into similar teeth cut in a set of disks carrying the gatings. The disks are mounted on a stud which can be moved by a key from the back of the lock in such a way that while the main stump is in the gatings—keeping the disks in position—the disks are carried forward out of gear with the levers; the key can then be removed and another having steps of suitable length inserted and turned so as to raise the levers, the disks being then brought back into gear.
| Fig. 15. |
Both the above locks require that the key steps should have certain definite lengths corresponding to the teeth, but a later lock resembling to some extent that brought out by Hobbs, Hart & Co. has been introduced by the Chatwood Co., in which it is sufficient after unlocking the lock to file any of the key steps and so alter the pattern of the key in any way. In this lock, which is illustrated in fig. 14, unlike all those that have been described, the levers are not pivoted but slide upon guide stumps; the main stump is divided as in Hobbs Hart’s lock, the various pieces being clamped together by a screw to form a solid stump. The sliders composing the main stump are not provided with teeth, the changing being effected as follows: when the bolt is partly shot by the correct key, the screw which binds the sliders together as it comes opposite an opening in the back of the case is loosened, the key is removed and altered—or a fresh key substituted—and is inserted so as to lift the levers to their correct height and expose the clamping screw at the back, which is then tightened. This lock is now commonly used for safe deposits, combined with a small lever lock of which the custodian carries the key, and which either blocks the bolt of the main lock or covers the keyhole.
In connexion with changeable key locks requiring key steps of definite lengths, much ingenuity has been displayed in designing keys with movable bits or steps, as fig. 15, which are useful chiefly as duplicates, being built up to match the key from time to time in use, and then deposited in some bank or other secure place to be used in case of emergency.