Encyclopaedia Britannica, 11th Edition, "Matter" to "Mecklenburg" / Volume 17, Slice 8

by Various

Fig. 121.

A chain built up of three turning pairs and one sliding pair, and known as the slider crank chain, is shown in fig. 121. It will be seen that the piece A1 can only slide relatively to the piece B1, and these two pieces therefore form the sliding pair. The piece A1 carries the pin B4, which is one half of the turning pair A4 B4. The piece A1 together with the pin B4 therefore form a kinematic link A1B4. The other links of the chain are, B1A2, B2B3, A3A4. In order to convert a chain into a mechanism it is necessary to fix one link in it. Any one of the links may be fixed. It follows therefore that there are as many possible mechanisms as there are links in the chain. For example, there is a well-known mechanism corresponding to the fixing of three of the four links of the slider crank chain (fig. 121). If the link d is fixed the chain at once becomes the mechanism of the ordinary steam engine; if the link e is fixed the mechanism obtained is that of the oscillating cylinder steam engine; if the link c is fixed the mechanism becomes either the Whitworth quick-return motion or the slot-bar motion, depending upon the proportion between the lengths of the links c and e. These different mechanisms are called inversions of the slider crank chain. What was the fixed framework of the mechanism in one case becomes a moving link in an inversion.

The Reuleaux system, therefore, consists essentially of the analysis of every mechanism into a kinematic chain, and since each link of the chain may be the fixed frame of a mechanism quite diverse mechanisms are found to be merely inversions of the same kinematic chain. Franz Reuleaux’s Kinematics of Machinery, translated by Sir A. B. W. Kennedy (London, 1876), is the book in which the system is set forth in all its completeness. In Mechanics of Machinery, by Sir A. B. W. Kennedy (London, 1886), the system was used for the first time in an English textbook, and now it has found its way into most modern textbooks relating to the subject of mechanism.

§ 81.* Centrodes, Instantaneous Centres, Velocity Image, Velocity Diagram.—Problems concerning the relative motion of the several parts of a kinematic chain may be considered in two ways, in addition to the way hitherto used in this article and based on the principle of § 34. The first is by the method of instantaneous centres, already exemplified in § 63, and rolling centroids, developed by Reuleaux in connexion with his method of analysis. The second is by means of Professor R. H. Smith’s method already referred to in § 23.

Method 1.—By reference to § 30 it will be seen that the motion of a cylinder rolling on a fixed cylinder is one of rotation about an instantaneous axis T, and that the velocity both as regards direction and magnitude is the same as if the rolling piece B were for the instant turning about a fixed axis coincident with the instantaneous axis. If the rolling cylinder B and its path A now be assumed to receive a common plane motion, what was before the velocity of the point P becomes the velocity of P relatively to the cylinder A, since the motion of B relatively to A still takes place about the instantaneous axis T. If B stops rolling, then the two cylinders continue to move as though they were parts of a rigid body. Notice that the shape of either rolling curve (fig. 91 or 92) may be found by considering each fixed in turn and then tracing out the locus of the instantaneous axis. These rolling cylinders are sometimes called axodes, and a section of an axode in a plane parallel to the plane of motion is called a centrode. The axode is hence the locus of the instantaneous axis, whilst the centrode is the locus of the instantaneous centre in any plane parallel to the plane of motion. There is no restriction on the shape of these rolling axodes; they may have any shape consistent with rolling (that is, no slipping is permitted), and the relative velocity of a point P is still found by considering it with regard to the instantaneous centre.

Reuleaux has shown that the relative motion of any pair of non-adjacent links of a kinematic chain is determined by the rolling together of two ideal cylindrical surfaces (cylindrical being used here in the general sense), each of which may be assumed to be formed by the extension of the material of the link to which it corresponds. These surfaces have contact at the instantaneous axis, which is now called the instantaneous axis of the two links concerned. To find the form of these surfaces corresponding to a particular pair of non-adjacent links, consider each link of the pair fixed in turn, then the locus of the instantaneous axis is the axode corresponding to the fixed link, or, considering a plane of motion only, the locus of the instantaneous centre is the centrode corresponding to the fixed link.

To find the instantaneous centre for a particular link corresponding to any given configuration of the kinematic chain, it is only necessary to know the direction of motion of any two points in the link, since lines through these points respectively at right angles to their directions of motion intersect in the instantaneous centre.

Fig. 122.

To illustrate this principle, consider the four-bar chain shown in fig. 122 made up of the four links, a, b, c, d. Let a be the fixed link, and consider the link c. Its extremities are moving respectively in directions at right angles to the links b and d; hence produce the links b and d to meet in the point Oac. This point is the instantaneous centre of the motion of the link c relatively to the fixed link a, a fact indicated by the suffix ac placed after the letter O. The process being repeated for different values of the angle θ the curve through the several points Oac is the centroid which may be imagined as formed by an extension of the material of the link a. To find the corresponding centroid for the link c, fix c and repeat the process. Again, imagine d fixed, then the instantaneous centre Obd of b with regard to d is found by producing the links c and a to intersect in Obd, and the shapes of the centroids belonging respectively to the links b and d can be found as before. The axis about which a pair of adjacent links turn is a permanent axis, and is of course the axis of the pin which forms the point. Adding the centres corresponding to these several axes to the figure, it will be seen that there are six centres in connexion with the four-bar chain of which four are permanent and two are instantaneous or virtual centres; and, further, that whatever be the configuration of the chain these centres group themselves into three sets of three, each set lying on a straight line. This peculiarity is not an accident or a special property of the four-bar chain, but is an illustration of a general law regarding the subject discovered by Aronhold and Sir A. B. W. Kennedy independently, which may be thus stated: If any three bodies, a, b, c, have plane motion their three virtual centres, Oab, Obc, Oac, are three points on one straight line. A proof of this will be found in The Mechanics of Machinery quoted above. Having obtained the set of instantaneous centres for a chain, suppose a is the fixed link of the chain and c any other link; then Oac is the instantaneous centre of the two links and may be considered for the instant as the trace of an axis fixed to an extension of the link a about which c is turning, and thus problems of instantaneous velocity concerning the link c are solved as though the link c were merely rotating for the instant about a fixed axis coincident with the instantaneous axis.

Fig. 123.	Fig. 124.