The average consumption of coal per mile, of thirteen of these engines, with the express trains between London and Bristol, during the half-year averaged 24.67 lb. per mile, the lowest being 23.22 lb., and the highest 26.17 lb., the average load being about eight coaches, or 243 tons. We have already seen that in 1849 the Great Western express ran at a higher rate than at present, being an exception to the general rule; and the fastest journey on record was performed at this time by one of these engines, when on May 14, 1848, the Great Britain took this Bristol express, consisting of four coaches and a van, to Didcot, fifty-three miles, in forty-seven minutes, or at the average speed of sixty-eight miles an hour. The maximum running speed was seventy-five miles an hour, and the indicated horse-power 1,000. A class of engines corresponding to this type in their general dimensions, but with 7 ft. coupled wheels, was introduced on the line, but it was not found successful. Through the courtesy of Mr. Dean, I am enabled to give a table showing the running speeds and loads of the principal express trains, broad and narrow gauge, to the West and North of England, run on the Great Western Railway.
| Train. | Speed to first stoppingstation. | Weight of train. | ||||
| Station. | Distance. miles. | Average speed--miles per hour. | Engine and tender. tons. | Carriages and vans, empty. tons. | Total | |
| BROAD GAUGE TO WEST OF ENGLAND: | ||||||
| 9.0 Paddington to Plymouth | Reading | 36 | 47 | 67 | 149 | 216 |
| 11.45 do. | Swindon | 77¼ | 53 | 67 | 104 | 171 |
| NARROW GAUGE TO THE NORTH | ||||||
| 10.0 Paddington to Birkenhead | Reading | 36 | 39.2 | 60 | 190 | 250 |
| 4.45 do. | Oxford | 63½ | 48.8 | 60 | 129 | 189 |
FIG 2.—GREAT WESTERN RAILWAY.
The narrow gauge trains are worked by two classes of engines. The first is a single engine with inside cylinders 18 in. diameter, 24 in. stroke. The driving wheels are 7 ft. diameter, and the leading and trailing wheels 4 ft. The frames are double, giving outside bearings to the leading and trailing axles, and outside and inside bearings to the driving axle; this arrangement gives a very steady running engine, and insures, as far as can possibly be done, safety in case of the fracture of a crank axle. The frames are 15 inches deep, of BB Staffordshire iron. The wheel base is, leading to driving wheels, 8 ft. 6 in; driving to trailing wheels, 9 ft.; total, 17 ft. 6 in. The boiler is of Lowmoor iron, 10 ft. 6 in. long and 4 ft. 2 in. outside diameter. The grate area is 17 square feet, and the heating surface is, tubes, 1,145½ square feet; fire-box 133 square feet; total, 1,278½ square feet. The boiler pressure is 140 lb. on the square inch, and the tractive power per lb. of mean pressure in cylinders, 92 lb. The weight in full working order is, engine, leading wheel, 10 tons; ditto driving wheels, 14 tons; ditto trailing wheels, 9 tons 10 cwt.; tender, with 40 cwt. coal and 2,600 gals. water, 26 tons 10 cwt.; total, 60 tons. These engines are extremely simple, but well proportioned, and are a very handsome type, and their average consumption of coal, working trains averaging ten coaches, is about 24.87 lb. per mile. The standard coupled passenger express engine on the narrow gauge has inside cylinders 17 in. diameter and 24 in. stroke; the coupled wheels are 6 ft. 6 in. diameter, and the leading wheels 4 ft.; the wheel base is 16 ft. 9 in. The frames are double, giving outside bearings to the leading axle, and inside bearings to the coupled wheels. The boiler is 11 ft. long by 4 ft. 2 in. diameter; the grate area is 16.25 square feet; and the heating surface is, tubes, 1,216.5 square feet; fire-box, 97.0 square feet; total, 1,313.5 square feet. The boiler pressure is 140 lb., and the tractive power per lb. of steam pressure in the cylinders, 88 lb. The weight in full working order is on the leading wheels, 10 tons 5 cwt.; driving wheels, 11 tons; trailing wheels, 9 tons 15 cwt.; total, 31 tons.
FIG. 3.—LONDON & NORTH-WESTERN RAILWAY.
FIG. 4—JOY'S VALVE GEAR.
Turning now to the London and North-Western Railway, we find that between 1862 and 1865 the express trains were worked with a handsome type of engines, known as the "Lady of the Lake" class. They have outside cylinders 16 in. diameter and 24 in. stroke, with single driving wheels of 7 ft. 6 in. diameter, and leading and trailing wheels 3 ft. 6 in. diameter, with a total wheel base of 15 ft. 5 in. The frames are single, with inside bearings to all the wheels. The boiler is 11 ft. long and 4 ft. diameter, and the heating surface is in the tubes, 1,013 feet; fire-box, 85 ft.; total, 1,098 feet. The tractive power per lb. of steam pressure in the cylinders is 68 lb. The weight in full working order is on the leading wheels, 9 tons 8 cwt.; driving wheels, 11 tons 10 cwt.; trailing wheels, 6 tons 2 cwt.; total, 27 tons. The tender weighs 17½ tons in working order. These engines burn about 27 lb. of coal per mile with trains of the gross weight of 117 tons, which is not at all an economical duty. About 1872, the weight of the heavier express trains on the North-Western had so increased, that a new standard type for this service was designed, and is now the standard passenger engine; it has inside cylinders 17 in. diameter and 24 in. stroke; the driving and trailing wheels are coupled, and are 6 ft. 6 in. diameter, and the leading wheels 3 ft. 6 in. The frames of steel are single, with inside bearings to all the wheels, and the boiler, of steel, is 9 ft. 10 in. long and 4 ft. 2 in. diameter. The steel used has a tensile strength of 32 to 34 tons per square inch, all the rivets are put in by hydraulic pressure, and the magnetic oxide on the surface of the plates where they overlap is washed off by a little weak sal-ammoniac and water. In testing, steam is first got up to 30 lb. on the square inch, the boiler is then allowed to cool, it is then proved to 200 lb. with hydraulic pressure, and afterward to 160 lb. with steam. The fire-box is of copper, fitted with a fire brick arch for coal burning, and the grate area is 15 square feet. The heating surface is, in the tubes, 1,013 square feet; fire-box, 89 square feet; total, 1,102 square feet. The wheel base is 15 ft. 8 in., and the tractive power 88 lb. for each lb. of steam pressure in the cylinders. These engines, working the fast passenger trains at a speed of about 45 miles per hour, burn about 35 lb. of coal per mile, when taking trains weighing about 230 tons gross. A variation from this type has been adopted on the Northern and Welsh sections, known as the "Precursor" class. These engines have 5 ft. 6 in. coupled wheels, and weigh 31 tons 8 cwt. in working order, but in other respects are very similar to the standard engines just described; with the Scotch express, averaging in total weight 187 tons, between Crewe and Carlisle, over heavy gradients, they burn 33 lb. of coal per mile. These engines, although much more powerful than the standard type, are not nearly of so handsome an appearance, the drivers seeming much too small for the boiler under which they are placed. But by far the boldest innovation on existing practice is the new class of compound locomotives now being introduced by Mr. Webb. It is a six wheel engine, with leading wheels 4 ft. diameter, and two pairs of drivers, 6 ft. 6 in. diameter. The trailing drivers are driven by a pair of outside cylinders, 18 in. diameter and 24 in. stroke; and the leading drivers by a single low-pressure cylinder—which takes the exhaust steam from the high-pressure cylinders—of 26 in. diameter and 24 in. stroke, placed under the center of the smoke-box. The boiler is the same as that in the standard type of engine, but the wheel base is 17 ft. 7 in., and in order to allow it to traverse curves easily, the front axle is fitted with a radial axle-box, which is in one casting from journal to journal, and fitted at each end with brass steps for the bearings; the box is radial, struck from the center of the rigid wheel base, and the horn plates are curved to suit the box, the lateral motion being controlled by strong springs. Another peculiarity of this engine is that, instead of the ordinary link motion, it is fitted with Joy's valve gear, which is now being more and more adopted. This gear—which is of a most ingenious decription—dispenses altogether with eccentrics, and so allows the inside bearings to be much increased, those on these engines being 13½ in. long; and it is also claimed for it that it is simpler and less costly, weighs less, and is more correct in its action than the ordinary link motion; the friction is less, the working parts are simplified, it takes less oil, and is well under the driver's eye. It also allows larger cylinders to be got in between the frames of inside cylinder engines, as, the slide valves may be placed on the top or bottom of the cylinders. This latter advantage is a great one, as, with the ordinary link motion, large cylinders are exceedingly difficult to design so as to get the requisite clear exhaust. The action of the gear is as follows: A rod, a, is fixed by a pin at b, on which it is free to turn, and is attached to a rod, c, at d, the other end of which link is fastened to the connecting rod at e. At the point, f, in this rod another lever, g, is connected to it, the upper end of which is coupled to the valve rod, h, at i, and just below this point a second connection is made to a block at j, sliding in a short curved piece, k. The inclination of the block, k, governs the travel of the valve. The total weight of the engine in working order is: On the leading wheels, 10 tons 8 cwt.; front drivers, 14 tons 4 cwt.; rear drivers, 13 tons 10 cwt.; total, 37.75 tons. The tender weighs 25 tons in full working order. The boiler pressure is 150 lb., and the usual point of cut-off in the high pressure cylinders, when running at speed, is half-stroke, while the pressure of steam admitted to the large cylinder is never to exceed 75 lb. per square inch. The average consumption of coal between London and Crewe is 26.6 lb. per train mile, or about 8 lb. per mile less than the standard coupled engine. In an experiment made in October, 1883, one of these engines took the Scotch express from Euston to Carlisle at an average speed, between stations, of 44 miles an hour, the engine, tender, and train weighing 230 tons, with a consumption of 29½ lb. of coal per mile, and an evaporation of 8.5 lb. of water per pound of fuel.