Fig. 2 shows the development of centre line and tangents. Set up all the treads and risers as they occur on the centre line of rail, Fig. 1. Draw the springing through A and E. Draw the centre falling line resting on the corners of square step at bottom and 4 inches above the landing at top. It is better for the falling line to be a little higher over the winders, especially near the top. To develop the tangents make the distance between the lines 1 2 3 D E equal A B C D E, Fig. 1. Draw D E level. From the centre joint on the falling line square out a line to cut the line 3 at C, join D C extended to cut the line 2 in B. From where the falling line cut the lower springing, square out a line to cut the line 1 in A; join A B; then A B C will be the tangents for the lower wreath and C D E for the top. Decide where the joint is to be below the springing, and draw a line parallel to the tangent A B, and tangent to the curve of the falling line where the joint is to be. The joint must be square to this line. It will be necessary to have a ramp here to ease into the straight rail, this is shown by the dotted lines. In the next plate is shown a method of easing the wreath into the straight rail without the aid of a ramp.
Fig. 3 shows the bottom face mould. Make C B F and B A equal C B A and B A, Fig. 2, and F A equal F A, Fig. 1, and complete the mould as usual. To find what each section is out of the centre of the plank, make W 4 5, Fig. 2, equal C 4 5 on the centre line of rail, Fig. 1; make 4 4 and 5 5, Fig. 2, equal N O and N H, Fig. 3. The difference between the falling line and 4 is what the section 4 on the minor axis is above the centre; and that between 5 and the falling line is what the section 5 is out of the centre. The section at both joints is in the centre, but at the springing A the falling line is a little above the centre, as it cut the springing above the level line A W, which is the height of the centre of the plank there. Get out the mould for the opposite side of the plank in the usual way, by laying Fig. 3 on a thin piece of stuff, and transfer the tangents and section lines on to it. Stick a bradawl through A 5 4 C and mark off out to it A 7 5 8 and 5 9, and C 10 and C 11, only on the opposite side. Work the inside and outside off first with a gig-saw, as before described. The shaded parts of sections at Fig. 4 show the superfluous stuff there is to come off the top side.
Fig. 5 shows the face mould for the top half. Draw C D E at right angles, and to equal C D E, Fig. 2. To see what the sections are out of the centre, make E 3 2, Fig. 2, equal E 3 2 on centre line of rail, Fig. 1. Make 2 2 and 3 3, Fig. 2, equal S R and S L. The difference between 2 and the falling line is what the section 2 is below the centre of plank, and that between 3 and the falling line is what the section 3 is below the centre. And that between E and the falling line is what it is below there.
Fig. 6 shows the sections, and the shaded part shows the superfluous stuff there is to come off the top at each section, after the inside and outside have been cut off.
Fig. 7 shows the wreath after the inside and outside have been cut off; the dotted lines show the wreath cut square through the plank.
PLATE 22.
PLATE XXII.
WINDERS IN THE HALF-SPACE, WITH A STRAIGHT FLIGHT ABOVE AND BELOW, WREATH TO FORM ITS OWN EASING.
Fig. 1 shows the plan with face of risers laid down. It will be noticed that the winders commence at the springing at the top, while they are brought past the springing at the bottom; this causes the rail to be high at E and, therefore, safer for any one coming down the stairs with their hand on the rail; and by bringing the winders below the springing it makes a better easing into the straight rail. This will be understood by referring to Fig. 2, where the centre line and tangents are developed. Set up the treads and risers as they occur on the centre line of rail, Fig. 1; also draw the springing and the centre line W. Draw the centre falling line resting on the corners of square steps top and bottom, and continue it up over the winders as shown by the dotted line. To develop the tangents make the distance between 1 2 3 4 5 equal A B C D E, Fig. 1. From where the falling line cuts the centre line square out a level line to cut the line 3 at C. Continue the top tangent down in a line with the straight rail to cut the line 4 in D. Join D C extended to cut the line 2 in B. Now make the joint below the springing, as near to it as possible, so that it will be clear of the easing. There being no ramp on the straight rail, the joint should be well clear of the easing and into the straight so as to avoid any signs of a cripple when the wreath is jointed to the straight rail, which there would be if the joint was made in the easing. Square out a level line from the joint P, and make P R equal the distance between the line 1 and the springing. Join R B, this has cut the line 1 at A. From A draw A W level. From R draw the joint square to the straight rail, and R P square to the tangent A B R. Make D F, Fig. 1, equal 4 F, Fig. 2, and join F E for the horizontal trace of the top wreath. Make B S, Fig. 1, equal 6 S, Fig. 2, and join S A for the horizontal trace of the bottom wreath.