Skin boat.
The size of skin or canvas-covered boats will usually be determined by the available amount of skin or covering material. Any waggon ox requires 8ft. of room to work in, and his skin would give a square of leather of very little over 6ft.; the African buffalo would be about the same, the eland somewhat larger, the black or brindled gnoo, the koodoo, and some of the larger antelopes, rather less. Suppose you have two ox skins; cut them straight across where the neck is at its widest, and let the natives or waggon-drivers stitch them together with strong sinews or thongs of hide, using a round awl or piercer, to make a round hole that will close again, and not a sharp-edged one that will cut the hide and so leave holes that will afterwards become leaks. The sheet should be kept damp, not wet, by spreading ox-dung or damp earth upon it till the frame is ready. Suppose it now to be 12ft. long and 6ft. wide; you may make your boat of from 3ft. to 4ft. in width, and 10ft. in length and 2ft. deep. If you care to have definite stem and stern posts, it is very likely that poles may be found with branches projecting at the required angle, but practically it is best to let them curve more or less gradually into the line of the keel, and for this purpose to choose two long straight poles; bend their thick ends round a tree to rather more than the requisite curve, as they will always straighten again; then, having chosen a flat piece of stiff ground, make two holes 10ft. apart, for the thick ends of your poles to rest in, bend down their thin ends, let them overlap, the farther the better, and lash them together; then take another of about 8ft. (or a foot longer on each side than the width of the skin), and having curved this, stick the ends into the ground, about 3½ ft. or 4ft. apart, and lash it where its centre passes under the keel; do the same with two others, 18in. on either side, and you will have the three midship frames; take two poles for each gunwale, join them by overlapping their thin ends as before, lash them to these central frames, so far from the keel that the edge of the skin will just cover them, bend them till they come together at the bow and stern, let them cross each other by a few inches, lash them tightly, and do not be in a hurry to cut their ends too closely; the curve they take will guide you in the insertion of the other frames. As you come nearer to the bow and stern, forked branches of the proper angle may be advantageously used, and along the sides, where the rowlocks come, forks may be left on the extremities of the ribs to serve for them; a fork may also be lashed in at either end for steering or sculling. Lay two or more ribbands or bilge pieces along each side; fasten in such boards or poles as you have for thwarts, and, when the whole is firmly lashed together, spread over it the prepared hide and stitch it all round to the pole that serves for gunwale, the hair, if you have not already scraped it off, being inwards; grease plentifully while it is still wet, and then let it dry; look carefully to the seaming; give this as much grease as it will absorb, or you can afford; and when it is quite stiff, saw off the superfluous timber ends, not too close; turn it up, and it is ready for use: never let your boat lie in the water longer than is absolutely necessary, and turn it bottom upwards whenever you haul it ashore. The quagga hide is proverbially rigid; and we should think that if taken off by merely making one slit along the belly, distending with dry sand and letting it harden in the sun, it would make a tolerably safe boat in smooth water for one person, without any other fitting.
We have heard of mules or transport animals being killed when water carriage became available; their flesh jerked for future provision, and even their ribs pressed into service to do duty without even a change of name in the canoes for which their hides served as coverings.
Russian cargo boat.
In the United Service Museum is a very carefully-constructed model of a Russian cargo boat from the Aleutian Islands, Commander Pike, R.N., the donor, states that it carries 3½ tons of fur sealskins. No metal is used in it, the wooden frame is pegged or lashed together, and covered with walrus hide. No dimensions are given; but, as very nearly three feet are required for one oarsman, it is probable that the boat would be 25ft. long and 8ft. wide near the stern; it will be noticed that there are but single thole pins, and therefore grummets of rope or iron must be fastened on the oars.
Esquimaux boats.
The other boat is the oomiak, or woman’s canoe, of the Esquimaux. The frame is made of drift wood and bone, often in very small pieces, but so tightly pegged and lashed together with hide thongs, that the compound seems fully as strong as a single piece; it is very neatly covered with sealskin.
RUSSIAN AND ESQUIMAUX SKIN BOATS