Winnings Made with Monoplanes.
Operators of monoplanes won a fair share of the cash prizes. They won $30,283 out of a total of $63,250, to say nothing about Grahame-White's winnings. The latter won $13,600, but part of his winning flights were made in a Bleriot monoplane, and part in a Farman machine. Aside from Grahame-White the winnings were divided as follows: Moissant (Bleriot) $13,350; Latham (Antoinette) $8,183; Aubrun (Bleriot) $2,400; De Lesseps (Bleriot) $2,300; Drexel (Bleriot) $1,700; Radley (Bleriot) $1,300; Simon (Bleriot) $750; Andemars (Clement-Bayard) $100; Barrier (Bleriot) $100.
Out of a total of $30,283, operators of Bleriot machines won $21,900, again omitting Grahame-White's share. If the winnings with monoplane and biplane could be divided so as to show the amount won with each type of machine the credit side of the Bleriot account would be materially enlarged.
The Most Popular Monoplanes.
While the number of successful monoplanes is increasing rapidly, and there is some feature of advantage in nearly all the new makes, interest centers chiefly in the Santos-Dumont, Antoinette and Bleriot machines. This is because more has been accomplished with them than with any of the others, possibly because they have had greater opportunities.
For the guidance of those who may wish to build a machine of the monoplane type after the Santos-Dumont or Bleriot models, the following details will be found useful.
Santos-Dumont—The latest production of this maker is called the "No. 20 Baby." It is of 18 feet spread, and 20 feet over all in depth. It stands 4 feet 2 inches in height, not counting the propeller. When this latter is in a vertical position the extreme height of the machine is 7 feet 5 inches. It is strictly a one-man apparatus. The total surface area is 115 square feet. The total weight of the monoplane with engine and propeller is 352 pounds. Santos-Dumont weighs 110 pounds, so the entire weight carried while in flight is 462 pounds, or about 3.6 pounds per square foot of surface.
Bamboo is used in the construction of the body frame, and also for the frame of the tail. The body frame consists of three bamboo poles about 2 inches in diameter at the forward end and tapering to about 1 inch at the rear. These poles are jointed with brass sockets near the rear of the main plane so they may be taken apart easily for convenience in housing or transportation. The main plane is built upon four transverse spars of ash, set at a slight dihedral angle, two being placed on each side of the central bamboo. These spars are about 2 inches wide by 1 1/8-inch deep for a few feet each side of the center of the machine, and from there taper down to an inch in depth at the center bamboo, and at their outer ends, but the width remains the same throughout their entire length. The planes are double surfaced with silk and laced above and below the bamboo ribs which run fore and aft under the main spars and terminate in a forked clip through which a wire is strung for lacing on the silk. The tail consists of a horizontal and vertical surface placed on a universal joint about 10 feet back of the rear edge of the main plane. Both of these surfaces are flat and consist of a silk covering stretched upon bamboo ribs. The horizontal surface is 6 feet 5 inches across, and 4 feet 9 inches from front to back. The vertical surface is of the same width (6 feet 5 inches) but is only 3 feet 7 inches from front to back. All the details of construction are shown in the accompanying illustration.
Power is furnished by a very light (110 pounds) Darracq motor, of the double-opposed-cylinder type. It has a bore of 4.118 inches, and stroke of 4.724 inches, runs at 1,800 r. p. m., and with a 6 1/2-foot propeller develops a thrust of 242 1/2 pounds when the monoplane is held steady.
Bleriot—No. XI, the latest of the Bleriot productions, and the greatest record maker of the lot, is 28 feet in spread of main plane, and depth of 6 feet in largest part. This would give a main surface of 168 square feet, but as the ends of the plane are sharply tapered from the rear, the actual surface is reduced to 150 square feet. Projecting from the main frame is an elongated tail (shown in the illustration) which carries the horizontal and vertical rudders. The former is made in three sections. The center piece is 6 feet 1 inch in spread, and 2 feet 10 inches in depth, containing 17 square feet of surface. The end sections, which are made movable for warping purposes, are each 2 feet 10 inches square, the combined surface area in the entire horizontal rudder being 33 square feet. The vertical rudder contains 4 1/2 square feet of surface, making the entire supporting area 187 1/2 square feet.