OF THE NEEDLE MICROMETER.
Fig. 8. [Plate II. A], represents this micrometer. The first of this kind was made by my father, and was described by him in his Micrographia Illustrata. It consists of a screw, which has fifty threads to an inch; this screw carries an index, which points to the divisions on a circular plate, which is fixed at right angles to the axis of the screw. The revolutions of the screw are counted on a scale, which is an inch divided into fifty parts; the index to these divisions is a flower de luce marked upon the slider, which carries the needle point across the field of the microscope. Every revolution of the micrometer screw measures 1⁄50 part of an inch, which is again subdivided by means of the divisions on the circular plate, as this is divided into twenty equal parts, over which the index passes at every revolution of the screw; by which means, we obtain with ease the measure of one-thousandth part of an inch; for 50, the number of threads on the screw in one inch, being multiplied by 20, the divisions on the circular plate, are equal to 1000; so that each division on the circular plate shews that the needle has either advanced or receded one-thousandth part of an inch.
To place this micrometer on the body of the microscope, open the circular part F K H, Fig. 8. [Plate II. A], by taking out the screw G, throw back the semicircle F K which moves upon a joint at K, then turn the sliding tube of the body of the microscope, so that the small holes which are in both tubes may exactly coincide, and let the needle g of the micrometer have a free passage through them; after this, screw it fast upon the body by the screw G.
The needle will now traverse the field of the microscope, and measure the length and breadth of the image of any object that is applied to it. But further assistance must be had, in order to measure the object itself, which is a subject of real importance; for though we have ascertained the power of the microscope, and know that it is so many thousand times, yet this will be of little assistance towards ascertaining an accurate idea of its real size; for our ideas of bulk being formed by the comparison of one object with another, we can only judge of that of any particular body, by comparing it with another whose size is known: the same thing is necessary, in order to form an estimate by the microscope; therefore, to ascertain the real measure of the object, we must make the point of the needle pass over the image of a known part of an inch placed on the stage, and write down the revolutions made by the screw, while the needle passed over the image of this known measure; by which means we ascertain the number of revolutions on the screw, which are adequate to a real and known measure on the stage. As it requires an attentive eye to watch the motion of the needle point, as it passes over the image of a known part of an inch on the stage, we ought not to trust to one single measurement of the image, but ought to repeat it at least six times; then add the six measures thus obtained together, and divide their sum by six, or the number of trials; the quotient will be the mean of all the trials. This result is to be placed in a column of a table, next to that which contains the number of the magnifiers.
By the assistance of the sectoral scale, we obtain with ease a small part of an inch. This scale is shewn at Fig. 5, 6, 7. [Plate II. A], in which the two lines c a c b, with the side a b, form an isosceles triangle; each of the sides is two inches long, and the base one-tenth of an inch. The longer sides may be of any given length, and the base still only of one-tenth of an inch. The longer lines may be considered as the line of lines upon a sector opened to one-tenth of an inch. Hence, whatever number of equal parts c a c b are divided into, their transverse measure will be such a part of one-tenth as is expressed by their divisions. Thus, if it be divided into ten equal parts, this will divide the inch into one-hundred equal parts; the first division next c will be equal to one-hundredth part of an inch, because it is the tenth part of one-tenth of an inch. If these lines be divided into twenty equal parts, the inch will be by those means divided into two hundred equal parts. Lastly, if a b c a be made three inches long, and divided into one-hundred equal parts, we obtain with ease the one-thousandth part. The scale is represented as solid at Fig. 6, but as perforated at Fig. 5 and 7; so that the light passes through the aperture, when the sectoral part is placed on the stage.
To use this scale, first fix the micrometer, Fig. 8. [Plate II. A], to the body of the microscope; then fit the sectoral scale, Fig. 7, in the stage, and adjust the microscope to its proper focus or distance from the scale, which is to be moved till the base appears in the middle of the field of view; then bring the needle point g, Fig. 8, by turning the screw L, to touch one of the lines c a exactly at the point answering to 20 on the sectoral scale. The index a of the micrometer, Fig. 8, is to be set to the first division, and that on the dial plate to 20, which is both the beginning and end of its divisions; we are then prepared to find the magnifying power of every magnifier in the compound microscope which we are using.
Example. Every thing being prepared agreeable to the foregoing directions, suppose you are desirous of ascertaining the magnifying power of the lens marked No. 4; turn the micrometer screw, until the point of the needle has passed over the magnified image of the tenth part of one inch; then the division, where the two indices remain, will shew how many revolutions, and parts of a revolution, the screw has made, while the needle point traversed the magnified image of the one-tenth of an inch; suppose the result to be twenty-six revolutions of the screw, and fourteen parts of another revolution, this is equal to 26 multiplied by 20, added to 14; that is, 534 thousandth parts of an inch.
The twenty-six divisions found on the strait scale of the micrometer, while the point of the needle passed over the magnified image of one-tenth part of an inch, were multiplied by 20, because the circular plate C D, Fig. 8, is divided into twenty equal parts; this produced 520; then adding the fourteen parts of the next revolution, we obtain 534 thousandth parts of an inch, or 5-tenths and 34-hundredth parts of another tenth, which is the measure of the magnified image of 1-tenth of an inch, at the aperture of the eye glasses, or at their foci. Now if we suppose the focus of the two eye-glasses to be one inch, the double thereof is two inches; or if we reckon in the thousandth part of an inch, we have two thousand parts for the distance of the eye from the needle point of the micrometer. Again, if we take the distance of the image from the object at the stage at six inches, or six thousandths, and add thereto two thousand, double the distance of the focus of the eye glass, we shall have eight thousand parts of an inch for the distance of the eye from the object; and as from the proposition, [page 51], we gather that the glasses double the image, we must double the number 534 found upon the micrometer, which then makes 1068: then, by the following analogy, we shall obtain the number of times the microscope magnifies the diameter of the object; say, as 240, the distance of the eye from the image of the object, is to 800, the distance of the eye from the object, so is 1068, double the measure found on the micrometer, to 3563, or the number of times the microscope magnifies the diameter of the object. By working in this manner, the magnifying power of each lens used with the compound microscope may be easily found, though the result will be different in different compound microscopes, varying, according to the combination of the lenses, their distance from the object, and one another, &c.
Having discovered the magnifying power of the microscope, with the different object lenses that are used therewith, our next subject is to find out the real size of the objects themselves, and their different parts; this is easily effected, by finding how many revolutions of the micrometer-screw answer to a known measure on the sectoral scale, or other object placed on the stage; from the number thus found, a table should be constructed, expressing the value of the different revolutions of the micrometer with that object lens, by which the primary number was obtained. Similar tables must be constructed for each object lens. By a set of tables of this kind, the observer may readily find the measure of any object he is examining; for he has only to make the needle point traverse over this object, and observe the number of revolutions the screw has made in its passage, and then look into his table for the real measure which corresponds to this number of revolutions, which is the measure required.
ACCOUNT OF GLASS, PEARL, &c. MICROMETERS, BY THE EDITOR.
Having seen some glass, &c. micrometers with exquisite fine divisions, for the purposes of applying to microscopes and telescopes; and in accuracy, being equivalent to the micrometer just described by our author, I judge, some account of their application and uses here will be very acceptable to the curious and inquisitive reader. A particular description of these as made by the ingenious Mr. Coventry, has been already given in the Encyclopædia Britannica, Vol. XI. p. 708.
The singular dexterity which Mr. Coventry and others now possess, of cutting by an engine fine parallel lines upon glass, pearl, ivory, and brass, at such minute distances as, by means of a microscope, are proved to be from the 100th to the 5000dth part of an inch, render this sort of micrometer the easiest and most accurate means of obtaining the exact natural size of the object to be magnified, and how many times that object is magnified. Mr. B. Martin, and other opticians, many years ago applied divided slips of glass, ivory, and horn to the body, in the focus of the eye glass of microscopes; but the thickness of the whole medium of the glass was found to diminish the distinct view of the object: ivory and horn, from their variable texture, were found to expand and contract too readily to be commodious. It is therefore to Mr. Cavallo that we are indebted for the happy thought of adapting slips of divided pearl to telescopes, to ascertain their power, &c. which substance the opticians now find to be the best for microscopical micrometers. It possesses a sufficient degree of transparency, when made about the thickness of writing paper; is a steady substance; admits very easily of the finest graduations, and is generally made in breadth about the 20th part of an inch.
Fig. 9. [Plate II. A], is a representation of this scale, with divisions of the 200ths of an inch, every fifth and tenth division being left longer than the others, which only go to about the middle. If the eye glass of the microscope or telescope, to which this micrometer is to be applied, magnify very much, its divisions may be proportionably minute.
To measure by this micrometer the size of an object in a single microscope, nothing more is required than to lay it on the micrometer, and adjust it to the focus of the magnifier, noticing how many divisions it covers or coincides with. Supposing the parallel lines to be the 1000dths of an inch, and the object covers two divisions, its real size is the 500th of an inch; if five, 200th of an inch, &c.
To find how much the object is magnified, is not so easily done by the single, as by the compound microscope, as has been before explained. The following simple method has been adopted by Mr. Coventry, and which may be considered tolerably accurate. Adjust a micrometer under the microscope, suppose 100th of an inch of divisions, with a small object on it, if square, the better; notice how many divisions one side of the object covers, suppose ten; then cut a piece of white paper something larger than the magnified appearance of the object; fix one eye on the object through the microscope, and the other at the same time on the paper, lowering it down till the object and the paper appear level and distinct: then cut the paper till it appear exactly the size of the magnified object; the paper being then measured, suppose an inch square: now, as the object under the magnifier, which appeared to be one inch square, was in reality only ten hundredths, or the tenth of an inch, the experiment proves that it is magnified ten times in length, one hundred times in superficies, and one thousand times in cube, which is the magnifying power of the glass; and in the same manner a table may be made of the power of all the other glasses.
In using the compound microscope, the real size of the object is found by the same method as in the single; but to demonstrate the magnifying power to greater certainty, adopt the following method. Lay a two-feet rule on the stage, and a micrometer level with its surface, (an inch suppose, divided into 100 parts:) with one eye see how many of those parts are contained in the field of the microscope, suppose 50; and with the other, at the same time, look for the circle of light in the field of the microscope, which with a little practice will soon appear distinct; mark how much of the rule, from the center of the stage, is intersected by the circle of light, which will be half the diameter of the field. Suppose eight inches; consequently the whole diameter will be sixteen. Now, as the real size of the field by the micrometers appeared to be only 50 hundredths, or half an inch, and as half an inch is only one 32d part of 16 inches, it shews the magnifying power to be 32 times in length, 1024 superficies, and 32768 in cube or bulk. For accuracy, as well as for comparative observations, the rule should always be a certain distance from the eye; eight inches in general is a proper distance.
Another way, and the most easy for finding the magnifying power of compound microscopes, is by using two micrometers of the same divisions; one adjusted under the magnifier, the other fixed in the body of the microscope in the focus of the eye glass. Notice how many divisions of the micrometer in the body are seen in one division of the micrometer under the magnifier, which again must be multiplied by the power of the eye glass. Example: Ten divisions of the micrometer in the body are contained in one division under the magnifier; so far the power is increased ten times: now, if the eye glass be one inch focus, such glass will of itself magnify about eight times in length, which, with the ten times magnified before, will be eight times ten, or 80 times in length, 6400 superficies, and 512000 cube.
Fig. 10. [Plate II. A], represents the field of view of the compound microscope, with the pearl micrometer, as applied to the aperture in the body, called the eye stop; and a magnified micrometer that is laid on the stage, shewing that one of the latter contains ten of the former.
A set of ivory and glass micrometers, about six in number, besides one or two pearl ones for the eye stops, are generally packed up with the best sort of microscopes made by Messrs. W. and S. Jones, Opticians, Holborn. They are divided into lines and squares, from the 100th to the 1000dth parts of an inch; and, besides measuring the magnifying powers of microscopes, are generally found useful in measuring the diameters, proportions, &c. of opake and transparent objects, even of the minutest kind. The smallest divisions of the glass micrometer to be useful, are those divided into the 4000dth part of an inch; and as these may be crossed again with an equal number of lines in the same manner, they form squares of the SIXTEEN MILLIONTH part of an inch surface, each square of which appearing under the microscope true and distinct. And, even small as this is, animalculæ are found so minute as to be contained in one of these squares!
Glass micrometers with squares, applied to the solar microscope, divide the objects into squares on the screen in such a manner, as to render a drawing from it very easy; and are employed with great advantage in the lucernal microscope.
The micrometers are constructed with moveable frames or tubes, so as to be either applied or taken away in the readiest manner.
For the uses of the pearl micrometer as applied to the telescope, see Mr. Cavallo’s pamphlet descriptive of its use, 8vo. 1793, and the Philosophical Transactions for 1791.
CHAP. III.
A DESCRIPTION OF THE MOST APPROVED MICROSCOPES, AND THE METHOD OF USING THEM.
In the preceding chapter I have endeavoured to give a comprehensive view of the theory of the microscope, and the principles on which the wonderful effects of this instrument depend. I shall now proceed to describe the various instruments themselves, their apparatus, and the most easy and ready mode of applying them to use; selecting for description those that, from some peculiar advantage in their construction, or from the reputation of the authors who have recommended and used them, are in most general use. What is said of these will, I hope, be sufficient to enable the reader to manage any other kind that may fall in his way.
DESCRIPTION OF ADAMS’S IMPROVED AND UNIVERSAL LUCERNAL MICROSCOPE. Fig. 1. [Plate III.]
This microscope was originally thought of, and in part executed by my father; I have, however, so improved and altered it, both in construction and form, as to render it altogether a different instrument. The approbation it has received from the most experienced microscopic observers, as well as the great demand I have had for them, has fully repaid my pains and expenses, in bringing it to its present state of perfection.
As the far greater part of the objects which surround us are opake, and very few sufficiently transparent to be examined by the common microscopes, an instrument that could be readily applied to the examination of opake objects, has always been a desideratum. Even in the examination of transparent objects, many of the fine and more curious portions are lost, and drowned as it were in the light which must be transmitted through them; while different parts of the same object appear only as dark lines or spots, because they are so opake, as not to permit any light to pass through them. These difficulties, as well as many more, are obviated in the lucernal microscope; by which opake objects of various sizes may be seen with ease and distinctness; the beautiful colours with which most of them are adorned, are rendered more brilliant, without in the least changing their natural teints. The concave and convex parts of an object retain also their proper form.
The facility with which all opake objects are applied to this instrument is another considerable advantage, and almost peculiar to itself; as the texture and configuration of the more tender parts are often hurt by previous preparation, every object may be examined by this instrument, first as opake, and afterwards, if the texture will admit of it, as transparent.
The lucernal microscope does not in the least fatigue the eye; the object appears like nature itself, giving ease to the sight, and pleasure to the mind: there is also in the use of this instrument, no occasion to shut that eye which is not directed to the object.
A further advantage peculiar to this microscope is, that by it the outlines of every object may be taken, even by those who are not accustomed to draw; while those who can draw well, will receive great assistance, and execute their work with more accuracy, and in less time than they would otherwise have been able to have performed it in. Most of the designs for this work were taken with the lucernal microscope; and I hope the accuracy with which they are executed, will be deemed a sufficient testimony in favour of the instrument. In this point of view it will, I think, be found of great use to the anatomist, the botanist, the entomologist, &c. as it will enable them not only to investigate the object of their researches, but to convey to others accurate delineations of the subject they wish to describe.
By the addition of a tin lanthorn, transparent objects may be shewn on a screen, as by the solar microscope.
Transparent objects may be examined with this instrument in three or four different modes; from a blaze of light almost too great for the eye to bear, to that which is perfectly easy to it.
When this instrument is fitted up in the best way, it is generally accompanied with a small double and single microscope.
Fig. 1. [Plate III.] represents the IMPROVED LUCERNAL MICROSCOPE, mounted to view opake objects; A B C D E is a large mahogany pyramidical box, about fourteen inches long, and six inches square at its larger end, which forms the body of the microscope; it is supported firmly on the brass pillar F G, by means of the socket H, and the curved piece I K.
L M N is a guide for the eye, in order to direct it in the axis of the lenses; it consists of two brass tubes, one sliding within the other, and a vertical flat piece, at the top of which is the hole for the eye. The outer tube is seen at M N, the vertical piece is represented at L M. The inner tube may be pulled out, or pushed in, to adjust it to the focus of the glasses. The vertical piece may be raised or depressed, that the hole, through which the object is to be viewed, may coincide with the center of the field of view; it is fixed by a milled screw at M, which could not be shewn in this figure.
At N is a dove-tailed piece of brass, made to receive the dove-tail at the end of the tubes M N, by which it is affixed to the wooden box A B C D E. The tubes M N may be removed from this box occasionally, for the convenience of packing it up in a less compass.
O P a small tube on which the magnifiers are screwed.
O one of the magnifiers; it is screwed into the end of a tube, which slides within the tube P; the tube P may be unscrewed occasionally from the wooden body.
Q R S T V X a long square bar, which passes through the sockets Y Z, and carries the stage or frame that holds the objects; this bar may be moved backward or forward, in order to adjust it to the focus, by means of the pinion which is at a.
b e is a handle furnished with an universal joint, for more conveniently turning the pinion. When the handle is removed, the nut, Fig. 2, may be used in its stead.
d e is a brass bar, to support the curved piece K I, and keep the body A B firm and steady.
f g h i is the stage for opake objects; it fits upon the bar Q R S T by means of the socket h i, and is brought nearer to, or removed farther from the magnifying lens, by turning the pinion a; the objects are placed in the front side of the stage, which cannot be seen in this figure, between four small brass plates; the edges of two of these are seen at k l. The two upper pieces of brass are moveable; they are fixed to a plate, which is acted on by a spiral spring that presses them down, and confines the slider with the objects; this plate, and the two upper pieces of brass, are lifted up by the small nut m.
At the lower part of the stage, there is a glass semiglobe n, which is designed to receive the light from the lamp, Fig. 3, and to collect and convey it to the concave mirror o, from whence it is to be reflected on the object.
The upper part, f g r S, of the opake stage takes out, that the stage for transparent objects may be inserted in its place.
Fig. 4. represents the stage for transparent objects; the two legs 5 and 6, fit into the under part r S of the stage for opake objects; 7 is the part which confines or holds the sliders, and through which they are to be moved; 9 and 10 a brass tube, which contains the lenses for condensing the light, and throwing it upon the object; there is a second tube within that, marked 9 and 10, which may be placed at different distances from the object by the pin 11.
When this stage is used as a single microscope, without any reference to the lucernal, the magnifiers or object lenses are to be screwed into the hole 12, and to be adjusted to a proper focus by the nut 13.
N. B. At the end A B of the wooden body there is a slider, which is represented as partly drawn out at A; when quite taken out, three grooves will be perceived, one of which contains a board that forms the end of the box, the next contains a frame with a greyed glass; the third, or that farthest from the end A B, two large convex lenses.
OF THE LAMP.
Fig. 3, represents one of Argand’s lamps, which is the most suitable for microscopic purposes, on account of the clearness, the intensity, and the steadiness of the light. The following method of managing it, with other observations, is copied from an account given by Mr. Parker, with those he sells.
The principle on which the lamp acts, consists in disposing the wick in thin parts, so that the air may come into contact with all the burning fuel, by which means, together with an increase of the current of air occasioned by rarefaction in the glass tube, the whole of the fuel is converted into flame.
The wicks are circular, and, the more readily to regulate the quantity of light, are fixed on a brass collar with a wire handle, by means of which they are raised or depressed at pleasure.
To fix the wick on, a wood mandril is contrived, which is tapered at one end, and has a groove turned at the other.
The wick has a selvage at one end, which is to be put foremost on the mandril, and moved up to the groove; then putting the groove into the collar of the wick-holder, the wick is easily pushed forward upon it.
The wick-holder and wick being put quite down in their place, the spare part of the wick should, while dry, be set alight, and suffered to burn to the edge of the tubes; this will leave it more even than by cutting, and, being black by burning, will be much easier lighted: for this reason, the black should never be intirely cut off.
The lamp should be filled an hour or two before it is wanted, that the cotton may imbibe the oil, and draw the better.
The lamps which have a reservoir and valve, need no other direction for filling, than to do it with a proper trimming pot, carefully observing when they are full; then pulling up the valve by the point, the reservoir being turned by the other hand, may be replaced without spilling a drop.
Those lamps which fill in the front like a bird-fountain, must be reclined on the back to fill, and this should be done gently, that the oil in the burner may return into the body when so placed and filled; if, by being too full, any oil appear above the guard, only move the lamp a little, and the oil will disappear; the lamp may then be placed erect, and the oil will flow to its proper level.
The oil must be of the spermaceti kind, commonly called chamber oil, which may generally be distinguished by its paleness, transparency, and inoffensive scent; all those oils which are of a red and brown colour, and of an offensive smell, should be carefully avoided, as their glutinous parts clog the lamp, and the impurities in such oil not being inflammable, will accumulate and remain in the form of a crust on the wick. Seal oil is nearly as pale and sweet as chamber oil, but being of a heavy sluggish quality, is not proper for lamps with fine wicks.
Whenever bad oil has been used, on changing it, the wick must also be changed, because, after having imbibed the coarse particles in its capillary tubes, it will not draw up the fine oil.
To obtain the greatest degree of light, the wick should be trimmed exactly even, the flame will then be completely equal.
There will be a great advantage in keeping the lamp clean, especially the burner and air tubes; the neglect of cleanliness in lamps is too common: a candlestick is generally cleaned every time it is used, so should a lamp; and if a candlestick is not to be objected to, because it does not give light after the candle is exhausted, so a lamp should not be thought ill of, if it does not give light when it wants oil or cotton; but this last has often happened, because the deficiency is less visible.
The glass tubes are best cleaned with a piece of wash leather.
If a fountain lamp be left partly filled with oil, it may be liable to overflow; this happens by the contraction of the air when cold, and its expansion by the warmth of a room, the rays of the sun, or the heat of the lamp when re-lighted: this accident may be effectually prevented by keeping the reservoir filled, the oil not being subject to expansion like air. On this account, those with a common reservoir are best adapted for microscopic purposes.
TO EXAMINE OPAKE OBJECTS WITH THE LUCERNAL MICROSCOPE.
The microscope is represented as mounted, and entirely ready for this purpose, in Fig. 1. [Plate III.]
To render the use of this instrument easy, it is usually packed with as many of the parts together as possible; it occupies on this account rather more room, but is much less embarrassing to the observer, who has only three parts to put on after it is taken out of its box, namely, the guide for the eye, the stage, and the tube with its magnifier.
But to be more particular, take out the wooden slide A, then lift out the cover and the grey glass from their respective grooves under the slide A.
Put the end N of the guide for the eye L M N into its place, so that it may stand in the position which is represented in this figure.
Place the socket, which is at the bottom of the opake stage, on the bar Q X T, so that the concave mirror o may be next the end D E of the wooden body.
Screw the tubes P O into the end D E. The magnifier you intend to use is to be screwed on the end o of these tubes.
The handle G b, or milled nut, Fig. 2, must be placed on the square end of the pinion a.
Place the lamp lighted before the glass lump n, and the object you intend to examine between the spring plates of the stage, and the instrument is ready for use.
In all microscopes, there are two circumstances which must be particularly attended to; the modification of the light, or the proper quantity to illuminate the object; secondly, the adjustment of the instrument to the focus of the glasses and the eye of the observer. In the use of the lucernal microscope there is a third circumstance, which is the regulation of the guide of the eye, each of which I shall consider by itself.
1. To throw the light upon the object. The flame of the lamp is to be placed rather below the center of the glass semiglobe n, and as near it as possible; the concave mirror o must be so inclined and turned, as to receive the light from the semiglobe; and reflect it thence upon the object; the best situation of the concave mirror, and the flame of the lamp, depends on a combination of circumstances, which a little practice will best point out.
2. To regulate the guide for the eye, or to place the center of the eye piece L, so that it may coincide with the focal point of the lenses, and the axis of vision. Lengthen and shorten the tubes M N by drawing out or pushing in the inner tube, and raising or depressing the eye-piece M L, till you find the large lens, which is placed at the end A B of the wooden body, filled by an uniform field of light, without any prismatic colours round the edge; for, till this piece be properly fixed, the circle of light will be very small, and only occupy a part of the lens; the eye must be kept at the center of the eye-piece L, during the whole of the operation; which may be rendered somewhat easier to the observer, on the first use of the instrument, if he hold a piece of white paper parallel to the large lenses, removing it from or bringing it nearer to them, till he finds the place where a lucid circle, which he will perceive on the paper, is brightest and most distinct, then to fix the center of the eye-piece to coincide with that spot; after which a very small adjustment will set it perfectly right.
3. To adjust the lenses to their focal distance. This is effected by turning the pinion a, the eye being at the same time at the eye-piece L. I often place the grey glass before the large lenses, while I am regulating the guide for the eye, and adjusting for the focal distance.
If the observer, in the process of his examination of an object, advance rapidly from a shallow to a deep magnifier, he will save himself some labour by pulling out the internal tube at O.
The upper part f g r s of the stage, is to be raised or lowered occasionally, in order to make the center of the object coincide with the center of the lens at O.
To delineate objects, the grey or rough ground glass must be placed before the large lenses; the picture of the object will be formed on this glass, and the outline may be accurately taken, by going over the picture with a pencil.
The opake part may be used in the day-time without a lamp, provided the large lenses at A B be screened from the light.
TO USE THE LUCERNAL MICROSCOPE IN THE EXAMINATION OF TRANSPARENT OBJECTS.
The microscope is to remain as before: the upper part f g r s of the opake stage must be removed, and the stage for transparent objects, represented at Fig. 4, put in its place; the end, Fig. 9 and 10, to be next the lamp.
Place the rough glass in its groove at the end A B, and the objects in the slider-holder at the front of the stage; then transmit as strong a light as you are able on the object, which you will easily do, by raising or lowering the lamp.
The object will be beautifully depicted on the rough glass: it must be regulated to the focus of the magnifier, by turning the pinion a.
The object may be viewed either with or without the guide for the eye; a single observer will see an object to the greatest advantage by using this guide, which is to be adjusted as we have described, [page 73]. If two or three wish to examine the object at the same time, the guide for the eye must be laid aside.
Take the large lens out of the groove, and receive the image on the rough glass; in this case the guide for the eye is of no use: if the rough glass be taken away, the image of the object may be represented on a paper screen.[29]
[29] A tin cover is sometimes made to go over the glass chimney of the lamp, Fig. 3, with only a small square aperture in front, sufficient to suffer the rays to pass into the microscope: this, by excluding all extraneous rays, adds in many cases most materially to the effect, particularly by day, and when objects are to be represented on the rough glass or screen only. Edit.
Take out the rough glass, replace the large lenses, and use the guide for the eye; attend to the foregoing directions, and adjust the object to its proper focus. You will then see the object in a blaze of light almost too great for the eye, a circumstance that will be found very useful in the examination of particular objects; the edges of the object in this mode will be somewhat coloured, but as it is only used in this full light for occasional purposes, it has been thought better to leave this small imperfection, than by remedying it, to sacrifice greater advantages; the more so, as this fault is easily corrected, and a new and interesting view of the object is obtained, by turning the instrument out of the direct rays of light, and permitting them to pass through only in an oblique direction, by which the upper surface is in some degree illuminated, and the object is seen partly as opake, partly as transparent. It has been already observed, that the transparent objects might be placed between the slider-holders kl of the stage for opake objects, and then be examined as if opake.
Some transparent objects appear to the greatest advantage when the lens at 9 and 10 is taken away; as, by giving too great a quantity of light, it renders the edges less sharp.
The variety of views which may be taken of every object, by means of the improved lucernal microscope, will be found to be of great use to an accurate observer: it will give him an opportunity of correcting or confirming his discoveries, and investigating those parts in one mode, which are invisible in another.
TO TRANSMIT THE IMAGE OF TRANSPARENT OBJECTS ON A SCREEN, AS BY THE SOLAR MICROSCOPE.
It has been long a microscopical desideratum, to have an instrument by which the image of transparent objects might be shewn on a screen, as by the common solar microscope; and this not only because the sun is so uncertain in this climate, and the use of the solar microscope requires confinement in the finest part of the day, when time seldom hangs heavy on the rational mind, but as it also affords an increase of pleasure, by displaying its wonders to several persons at the same instant, without the least fatigue to the eye.
This purpose is now effectually answered, by affixing the transparent stage, Fig. 4, of the lucernal to a lanthorn containing one of Argand’s lamps. The lamp is placed within the lanthorn, and the end 9, 10 of the transparent stage is screwed into a female screw, which is rivetted in the sliding part of the front of the lanthorn; the magnifying lenses are to be screwed into the hole represented at 12; they are adjusted by turning the milled nut. The quantity of light is to be regulated, by raising and lowering the sliding plate, or the lamp. N. B. This part, with its lanthorn and lamp, may be had separate from the lucernal microscope.[30]
[30] This effect by the lanthorn and lamp is subject to much limitation in the field of view, or circle of light thrown upon the screen. A circle of not more than from 12 to about 15 inches can ever be obtained with any tolerable strength of light, to shew the most transparent sort of objects that can be found, such as the scale of a sole fish, a fly’s wing, &c. The great difference between the light of the sun and a lamp is a natural obstacle to great performances in this way, and renders them far short of the effects of the solar microscope. The exhibition, however, is considerable, and much deserving of the notice of any observer disposed to this sort of apparatus. Probably, subsequent experiments may yet produce more light on this instrument. The best sort of apparatus for this purpose hitherto made, I shall describe in a [following section]. Edit.
APPARATUS WHICH USUALLY ACCOMPANIES THE IMPROVED LUCERNAL MICROSCOPE.
The stage, Fig. 1, f g h i, for opake objects, with its glass semiglobe, and concave mirror, which is moveable upon the bar Q R S T, and set readily to any distance by the screw at a. The glasses o and n are also moveable upon the bar for regulating and adjusting the light upon the object.
The stage, Fig. 4, for transparent objects, which fits on the upper part P S of the foregoing stage. When this is to be applied occasionally to a lanthorn for shewing transparent objects on a screen, &c. it is made of a much larger diameter, to admit of the illuminating lenses at 9, 10, and 11, of greater power of condensing the rays from the lamp.
The sliding tube O P, to which the magnifiers are to be affixed; one end of this is to be screwed on the end B of the wooden body; the magnifier in use is to be screwed to the other end on the inner tube. This tube slides inwards or outwards; it is first used to set the magnifier at nearly the right distance from the object, before the exact adjustment for the focus is made, by turning the pinion at a with Hook’s joint and handle b e.
Eight magnifying lenses in brass cells, Fig. 5. [Plate III.] these are so constructed that any two of them may be combined together, and thus produce a very great variety of magnifying powers. The cells unscrew to admit of the glasses being cleaned.
A fish-pan, such as is represented at Fig. 6, whereon a small fish may be fastened in order to view the circulation of its blood; its tail is to be spread across the oblong hole at the smallest end, and tied fast by means of the attached ribbon. The knob on its back is to be put through a slit hole on the brass piece, No. 5, of Fig. 4. The tail of the fish is to be brought then immediately before the magnifier.
A steel wire, Fig. 7, with a pair of nippers at one end, and a steel point at the other; the wire slides backwards or forwards, in a spring tube which is affixed to a joint at the bottom, on which is a pin to fit the hole in the leg, No. 6, Fig. 4. This is used to confine small objects.
A slider of brass, Fig. 8, containing a flat glass slider and a brass slider, into which are fitted some small concave glasses. It is for confining small living objects, and when used is placed between the two plates, No. 7, Fig. 4.
A pair of forceps, Fig. 9, by which any occasional small object may be conveniently taken up.
Six large ivory sliders, with transparent objects placed between two plates of talc, and confined by brass rings, and six small ditto with ditto. Fig. 10. The larger ones usually contain a set of Custance’s fine vegetable cuttings.
Fourteen wood sliders, containing on each four opake objects, and two spare sliders for occasional objects; all fitted to the cheeks kl of the stage. Fig. 11.
Some capillary tubes, Fig. 12, to receive small fish, and for viewing small animalcula. They are to be placed between the two plates of the stage No. 7, Fig. 4.
A small ivory double box, containing spare plates of talc and brass rings, for replacing any in the small ivory sliders, when necessary.
A single lens mounted in a tortoiseshell case, to examine minute objects previous to their being applied to the sliders.
Opake objects are easily put on the spare sliders by a wetted wafer; and, for good security, gum water may be added.
For the prices of the lucernal, as well as all the other sorts of microscopes, see the [list] annexed to these Essays.