DETERMINATION OF COPPER IN ORES
Copper ores vary widely in composition from the nearly pure copper minerals, such as malachite and copper sulphide, to very low grade materials which contain such impurities as silica, lead, iron, silver, sulphur, arsenic, and antimony. In nearly all varieties there will be found a siliceous residue insoluble in acids. The method here given, which is a modification of that described by A.H. Low (!J. Am. Chem. Soc.! (1902), 24, 1082), provides for the extraction of the copper from commonly occurring ores, and for the presence of their common impurities. For practice analyses it is advisable to select an ore of a fair degree of purity.
PROCEDURE.— Weigh out two portions of about 0.5 gram each of the ore (which should be ground until no grit is detected) into 250 cc. Erlenmeyer flasks or small beakers. Add 10 cc. of concentrated nitric acid (sp. gr. 1.42) and heat very gently until the ore is decomposed and the acid evaporated nearly to dryness (Note 1). Add 5 cc. of concentrated hydrochloric acid (sp. gr. 1.2) and warm gently. Then add about 7 cc. of concentrated sulphuric acid (sp. gr. 1.84) and evaporate over a free flame until the sulphuric acid fumes freely (Note 2). It has then displaced nitric and hydrochloric acid from their compounds.
Cool the flask or beaker, add 25 cc. of water, heat the solution to boiling, and boil for two minutes. Filter to remove insoluble sulphates, silica and any silver that may have been precipitated as silver chloride, and receive the filtrate in a small beaker, washing the precipitate and filter paper with warm water until the filtrate and washings amount to 75 cc. Bend a strip of aluminium foil (5 cm. x 12 cm.) into triangular form and place it on edge in the beaker. Cover the beaker and boil the solution (being careful to avoid loss of liquid by spattering) for ten minutes, but do not evaporate to small volume.
Wash the cover glass and sides of the beaker. The copper should now be in the form of a precipitate at the bottom of the beaker or adhering loosely to the aluminium sheet. Remove the sheet, wash it carefully with hydrogen sulphide water and place it in a small beaker. Decant the solution through a filter, wash the precipitated copper twice by decantation with hydrogen sulphide water, and finally transfer the copper to the filter paper, where it is again washed thoroughly, being careful at all times to keep the precipitated copper covered with the wash water. Remove and discard the filtrate and place an Erlenmeyer flask under the funnel. Pour 15 cc. of dilute nitric acid (sp. gr. 1.20) over the aluminium foil in the beaker, thus dissolving any adhering copper. Wash the foil with hot water and remove it. Warm this nitric acid solution and pour it slowly through the filter paper, thereby dissolving the copper on the paper, receiving the acid solution in the Erlenmeyer flask. Before washing the paper, pour 5 cc. of saturated bromine water (Note 3) through it and finally wash the paper carefully with hot water and transfer any particles of copper which may be left on it to the Erlenmeyer flask. Boil to expel the bromine. Add concentrated ammonia drop by drop until the appearance of a deep blue coloration indicates an excess. Boil until the deep blue is displaced by a light bluish green coloration, or until brown stains form on the sides of the flask. Add 10 cc. of strong acetic acid (Note 4) and cool under the water tap. Add a solution containing about 3 grams of potassium iodide, as in the standardization, and titrate with thiosulphate solution until the yellow of the liberated iodine is nearly discharged. Add 1-2 cc. of freshly prepared starch solution and titrate to the disappearance of the blue color.
From the data obtained, calculate the percentage of copper (Cu) in the ore.
[Note 1: Nitric acid, because of its oxidizing power, is used as a solvent for the sulphide ores. As a strong acid it will also dissolve the copper from carbonate ores. The hydrochloric acid is added to dissolve oxides of iron and to precipitate silver and lead. The sulphuric acid displaces the other acids, leaving a solution containing sulphates only. It also, by its dehydrating action, renders silica from silicates insoluble.]
[Note 2: Unless proper precautions are taken to insure the correct concentrations of acid the copper will not precipitate quantitatively on the aluminium foil; hence care must be taken to follow directions carefully at this point. Lead and silver have been almost completely removed as sulphate and chloride respectively, or they too would be precipitated on the aluminium. Bismuth, though precipitated on aluminium, has no effect on the analysis. Arsenic and antimony precipitate on aluminium and would interfere with the titration if allowed to remain in the lower state of oxidation.]
[Note 3: Bromine is added to oxidize arsenious and antimonious compounds from the original sample, and to oxidize nitrous acid formed by the action of nitric acid on copper and copper sulphide.]
[Note 4: This reaction can be carried out in the presence of sulphuric and hydrochloric acids as well as acetic acid, but in the presence of these strong acids arsenic and antimonic acids may react with the hydriodic acid produced with the liberation of free iodine, thereby reversing the process and introducing an error.]