Analysis of Horizontal Space Divisions
Two Horizontal Space Divisions
Rule 2a. If the primary mass is divided into two horizontal divisions, the dominance should be either in the upper or the lower section. [Plate 7] shows this division of the primary mass—the simplest division of the space. A space divided just half way from top to bottom would be monotonous and expressive of the ratio of one to one. This arrangement as we have already discovered in the [second chapter] is not conducive to good design.
By the stated rule, 2a, the varied adjustment of this double horizontal division affords all possible latitude for constructive purposes. It is better to place the division in such a manner that the upper division (or lower) will not appear pinched or dwarfed by comparison with the remaining area. Thus a ratio of one to three, or three to five, or five to eight is better than a ratio of one to one or one to eighteen, but there is no exact or arbitrary ruling on this point.
Two Horizontal Divisions in Wood
[Figure 8] illustrates two horizontal divisions in wood construction and also the freedom of choice as to exact proportions. The eye will be found a good judge of the proper spacings subject to the limitations already mentioned.
Plate 9
It is best to keep the design within the limits of two horizontal space divisions in designing cylindrical clay forms, particularly in the elementary exercises. Enough variety will be found to make pleasing arrangements, and the technical results obtained by two divisions are much better than those obtained from a greater number of divisions.
Two Horizontal Divisions in Clay
[Figures 14], [15], and [16], [Plate 9], are clay forms with the dominance placed in either the upper or lower portion of the primary mass. [Figure 13] has been used to illustrate the fact that horizontal space division principles are applicable to any material. The horizontal divisions in [Figure 13] are due to structural needs. A horizontal line carries this division across to [Figure 14], a clay vase. The horizontal division line now becomes the one which marks the widest part of the vase. It gives the same relation between the top and bottom horizontal spaces as in [Figure 13]. It marks an aesthetic point in the design of the vase, or a variation of the contour, introduced by reason of its effect upon the beauty of the vase, not called for by the needs of actual service.
A musical composition is often played in an orchestra first by the wood instruments, taken up and repeated by the brasses, then by the strings, and finally played as an harmonious whole by the entire orchestra. There is a close parallel in [Figure 12], an adaptation of one of Gustav Stickley's designs. The two-division rule is used in the relations of the plaster and wainscoting; again in the plaster over, and the cement or tile around the fireplace. It is repeated in the arrangement of the copper and cement of the fireplace facing and hood and in the door panels. By repeating again and again similar space divisions the wall space becomes a unified and harmonious whole. Variety is secured by the introduction of three horizontal divisions in the details of the wainscoting. This method of repeating similar space divisions is called "echoing" and is one of the most effective means known for securing the effect of unity.
Plate 10
Two Horizontal Divisions in Metal
The horizontal subdivisions in metal are usually made for service. [Figures 17], [18], and [19], [Plate 10], are examples of such divisions. The location of the clock face in [Figure 18] calls for the placing of its horizontal axis in accordance with Rule 2a. The lamp in [Figure 19] shows an instance where the entire design once divided by Rule 2a, may be again subdivided into a similar series of divisions. This arrangement is quite similar to the system of repetitions seen in [Figure 12] and termed "echoing" the original divisions.
Three Horizontal Space Divisions
Rule 2b. If the primary mass is divided into three horizontal divisions or sections, the dominance should be placed in the center section with varying widths in the upper and lower thirds.
When it becomes necessary to divide the primary mass into more than two sections the designer's problem becomes more difficult. With the addition of a greater number of horizontal divisions there is a manifest tendency for the design to become cut up into so many small sections that the simplicity of the whole mass is lost. Here, as elsewhere, that principle which we call unity or the quality of "holding together" is necessary and should be the constant test of the design. The instant any part of the design seems to fly apart from the main mass it becomes the designer's duty to simplify the design or pull the parts together and thus restore the lost unity.
As a restriction against loss of unity it is necessary to group all of the minor horizontal divisions into a system of two or three large horizontal divisions. Referring to Rule 2b, it is seen that when three divisions are used, it becomes the practice to accentuate the center section by making it larger. This arrangement is designed to give weight to the center portion and by this big stable division to hold the other subdivisions together and in unity.
Three Horizontal Divisions in Wood
Two horizontal masses and one vertical mass shown in [Figures 9], [10], and [11], [Plate 8], illustrate the application of this three-division rule to wood construction. It is seen that the construction of rails, doors, and shelves is responsible for the fixing of all of these divisions. It may also be seen that three divisions are applicable to either the vertical or the horizontal primary mass. [Figure 10] illustrates the violation of this type of spacing at the point A, where the shelves are no more pleasingly arranged than the rounds of a ladder. Later on we shall be able to rearrange these shelves in a pleasing manner but at present it is better to relieve the monotony by omitting the center shelf. This applies the three division rule to the satisfactory appearance of the desk at B.
Similar monotony in spacing is seen in the screen, [Figure 11]. The correction in B appeals at once as a far more satisfactory arrangement than that secured by placing the cross bar half way up as in A. There are no infallible rules for this readjustment beyond those already stated. The eye must in part be depended upon to guide the artistic sense aright.
Three Horizontal Divisions in Clay
It is suggested that it is desirable to keep clay forms within the limitations of two divisions. Rectangular posts, pedestals, and other vertical forms in cement may be developed by the application of Rule 2a or 2b, if care is taken to group all minor divisions well within the limitations of these rules.
The statement just made in reference to simplified groupings is illustrated in the candlestick and cup in [Figures 20] and [21], [Plate 10]. The construction based upon the three functions performed by the cup, the handle, and the base, suggests the use of these horizontal divisions. The minor curves have been subordinated to, and kept within, these three divisions. The final result gives a distinct feeling of unity impossible under a more complex grouping. The Greek column will afford an architectural illustration of a similar grouping system.
Three Horizontal Divisions in Metal
The lathe bed of [Figure 22] shows one of innumerable examples of space violations in the industrial arts. A slight lowering of the cross brace would add materially to the appearance and strength of the casting. [Figure 23] is a copper box with the following more or less common faults of design: commonplace ratio of length and width (2:1) partially counteracted, however, by a more pleasing ratio of the vertical dimension, equal spacing in the width of cover of box and box body, and equal spacing of the hinges of the box from the ends of the box and from each other. By applying the two and three horizontal division rules these errors may be avoided.
Freehand Curves
[Figure 24] shows a low bowl with a compass curve used in designing the contour. This has brought the widest part of the design in the exact center of the bowl which makes it commonplace. In addition to this the top and bottom are of the same width, lacking variety in this respect. Correction is readily made by applying a freehand curve to the contour, raising or lowering the widest point (F), at the same time designing the bottom either larger or smaller than the top.
INSTRUCTION SHEET
[Plate 7] is a sheet suggestive of the application of Rules 1a, 1b, 2a, and 2b, with an indication of the type of problem to be required. The steps of the designing processes in either wood (class 1), clay (class 2), or metal (class 3), are summarized as follows:
SUMMARY OF DESIGN STEPS
(a) Construction of the rectangle representing the vertical or horizontal character of the primary mass with desirable proportions. It is better to select a typical view ([Plate 6], D), preferably a front elevation.
(b) Subdivide this rectangle into two or three structural sections; horizontal in character. Make two or three trial freehand sketches for varied proportions and select the most pleasing one in accordance with Rules 1a, 1b, 2a, and 2b.
(c) Translate the selected sketch to a full size mechanical drawing or at least to a reasonably large scale drawing. The structural elements: i.e., legs, rails, posts, etc., should be added and other additional views made.
(d) Dimension and otherwise prepare the drawing for shop purposes.
(e) Construct the project.
SUGGESTED PROBLEMS
Design a nasturtium bowl, applying Rules 1a, 1b, 2a. Design a writing table 2 feet 6 inches high with three horizontal divisions.
SUMMARY OF RULES
Rule 2a. If the primary mass is divided into two horizontal divisions, the dominance should be either in the upper or the lower section.
Rule 2b. If the primary mass is divided into three horizontal divisions or sections, the dominance should be placed in the center section with varying widths in the upper and lower thirds.
REVIEW QUESTIONS
1. State two methods of subdividing the primary mass.
2. Define the nature and need of horizontal space divisions.
3. Give five steps to be used in designing a foot stool or piano bench.
4. What point constitutes a horizontal division in the contour of a simple clay bowl?
5. State the rule governing two horizontal space divisions and furnish illustrations in wood, clay, and metal.
6. Give the rule governing three horizontal space divisions and supply illustrations in wood, clay, and metal.
7. State five steps in the designing of a project in the industrial arts involving the use of horizontal structural divisions.
Plate 11
Chapter IV
VERTICAL MAJOR DIVISIONS OF THE PRIMARY MASS
Nature and Need of Vertical Space Division
The design of the primary mass has now been considered under Rules 1a and 1b, and its horizontal divisions under Rules 2a and 2b. The next logical step is the consideration of the nature of the lines that cross the primary mass in a vertical direction. In the original planning of the primary mass it was found that the horizontal bounding lines and the horizontal divisions were parallel to the base line of an object and that the base line was necessary to ensure stability. Vertical lines are necessary and equally important to give the needed vertical support to an object.
So accustomed is the eye to vertical lines in tree trunks, tall buildings, and thousands of other examples that the upward eye movement in viewing an object, having a predominance of vertical elements, seemingly adds to its height.
The designer thus has a most useful device with which to increase the apparent height of an object that, for structural or other reasons, must in reality not have great height. [Chapter III] drew attention to the influence of horizontal lines on a project. Vertical lines on an object are found to produce an analogous effect vertically.
Architectural Precedent for Vertical Divisions
Gothic cathedral builders used the vertical line, repeated again and again in buttresses, pinnacles, and spires to give great apparent height to a building and to make it a unified vertical mass of great beauty. The modern church spire, together with the long, vertical interior columns, similarly affects our present day church edifices.
Plate 12
This idea of repeating the vertical bounding lines of the primary mass by cutting the mass into vertical spaces is also useful in breaking up or destroying the monotony of large unbroken surfaces. Pilasters may cut the front of a building into interesting spaces; piers may break up the regularity of a long fence; legs and panels may, each for the same purpose, cross a cabinet. While some of these may be structurally necessary and some not, they are all witnesses to the desire to produce beauty in design. As these examples are so numerous in the industrial arts, it is well to study in detail their proper adaptation to our needs.
One Vertical Space Division
Upon analyzing one vertical space division, it will be found to be a primary mass, vertical in character and governed by Rule 1a. [Figure 25], [Plate 12], illustrates one vertical division. The foot is an appendage to be considered in [Chapter V].
Rule 3a. If the primary mass is divided into two vertical divisions, the divisions should be equal in area and similar in form. Exception may be made in case of structural requirements. By imagining two adjacent doors of equal size, the design effect of two vertical divisions may be made clear. [Plate 11] illustrates a rectangle (A) divided in this manner, preliminary to the development of a problem. [Figure 27], [Plate 12], represents the type of object to which the exception to the rule may be applied. In the design of this desk, the structure practically prohibits two equal vertical divisions, necessitating an unequal division in the section occupied by the drawers.
Two Vertical Space Divisions
In [Plate 12], [Figure 26], the designer had his vertical spacings dictated by service in the form of two doors. As service demands a tall vertical primary mass, it is but natural to design the doors to conform with the primary mass. This gives a monotonously long space for the glass panels and suggests structural weakness. To relieve this the designer applied Rule 2a and crossed the vertical panels by horizontal subdivisions, relieving the monotony and still retaining the unity of the primary mass.
Two Vertical Divisions in Wood
In [Figure 27] his problem was a variation of that presented in [Figure 26]. Structural limitations called for unequal divisions of the vertical space arrangement. The left portion of the desk becomes dominant as demanded by service. The drawer or brace is necessary in this design as it acts as a sort of link, binding the two vertical legs together. The omission of the drawer would destroy the unity of the mass.
Plate 13
Two Vertical Divisions in Clay
As vertical space divisions are principally applicable to rectilinear or flat objects and moreover as it is in such forms only that they have structural value, they are not commonly met in cylindrical pottery ware. Vertical divisions are, however, occasionally used in architectural tiles and other flat wall objects. As three divisions are much more commonly used in clay and cement, this material will now be left for later consideration in this chapter.
Vertical spacings in metal are quite similar to space divisions in wood. Wrought iron fences are, by reason of structural limitations composed of vertical and horizontal lines, varied by the introduction of piers and curved members. As they are typical of a certain branch of iron construction, two designs of the Anchor Post Iron Company have been introduced. [Figure 32], [Plate 14], represents two equal vertical divisions made so because of structural and aesthetic demands. The piers in this instance form a part of the general design of the entire gate and must be considered accordingly.
Vertical Divisions in Metal
The vertical subdivision in [Figure 32], [Plate 14], has been repeated or echoed by the long vertical bars, alternating with the shorter ones and producing pleasing variety. The horizontal divisions are designed according to Rule 2b. In designing the newel lantern in [Figure 34] the designer was required to form a vertical primary mass to conform with the similar mass of the post. This he determined to subdivide vertically in practically the same manner as the cabinet in [Figure 26]. Threatened with the same monotony he met the situation by subdividing the vertical sections into three horizontal divisions in accordance with Rule 2b. The structural supports, however, rising up in the center of this mass, destroy its unity. They would have carried out the lines of the structure of the newel post and continued the lines of the lantern better, if they had been attached to the corners rather than to the sides of the newel post.
Plate 14
Three Vertical Space Divisions
Rule 3b. If the primary mass is divided into three vertical divisions, the center division should be the larger, with the remaining divisions of equal size. A large building with a wing on either side will give an idea of this form of spacing. The size of the main building holds the wings to it, thus preserving the unity of the structure, while equal divisions on either side give balance. [Plate 11] (B) gives an example of a rectangle divided in this manner. This three-division motive is a very old one. In the middle ages painters and designers used three divisions or a triptych, as it is called, in their altar decorations. A painting of the Virgin was usually placed in the center division with a saint in each of the remaining panels to the right and left. Designers and mural decorators have been using the triptych ever since that period.
Three Vertical Divisions in Wood
The desk in [Figure 28], [Plate 12], is a good example of the three-vertical space rule. The drawer in the center forms the mid or dominant section and by its greater length holds the two smaller sections together. This design is better than [Figure 27], which has a similar mass. The prominent vertical lines in [Figure 27] counteract and destroy the effect of the long horizontal dominant lines of the table top, whereas in [Figure 28], the vertical lines in the center of the design are so short that they do not interfere with the horizontal lines of the table top. [Figure 28] supports the horizontal tendency of the primary mass while [Figure 27] neutralizes or practically destroys its character.
Three Vertical Divisions in Clay and Cement
[Figure 30], [Plate 13], represents an overmantle by the Rookwood Potteries. It is typical of a class of overmantles which may be developed in tiles or in cement, forming an agreeable contrast with the brick of a large fireplace. The three divisions or triptych should be proportionately related to the opening of the fireplace and to the enclosing mass of brick or wood work. We will consider [Figure 29] to show how this may be carried out.
[Figure 29] bears a strong resemblance to [Figure 12], [Plate 9], and is an elaboration of a simple three-division theme of spacing. The design seems to be complex until it is analyzed into two rules. The primary mass of the entire fireplace motive (including the surrounding panelling) has first been planned with strong and prominent horizontal lines. This was then divided vertically (A) to conform with Rule 3b, the three-division theme, giving the divisions for the bookcases and mantle. The horizontal divisions (B) were then constructed within the remaining space, affecting the distance from the picture moulding to the mantle and from the mantle to the floor line, in accordance with Rule 2a. That left the space of the width of the cement work (C) to be subdivided again by Rule 3b, while the top of the wainscoting panels re-echoed the previous horizontal divisions of Rule 2a. The fireplace opening merely carries out at D the same proportionate relation that dominates all vertical divisions, Rule 3b, while the wainscoting follows the general horizontal divisions of Rule 2a. By this method we have variety in spacing and unity through repetition of similar proportions.
Plate 15
The cement bench, [Figure 31], has a three-division arrangement to break up the monotony of the long rail, and at the same time to repeat the characteristics of a horizontal primary mass.
Three Vertical Divisions in Metal
[Figure 33], [Plate 14], is a common example of three vertical divisions in metal suggested by the needs of service. [Figures 35] and [36] are thin metal problems. The familiar pen tray is primarily a horizontal mass, so determined by its required service as a pen holder. The projecting handles form the outer divisions, and the spacing motive, Rule 3b, has been repeated in the raised projection, decorating the handles. The book rack in [Figure 36] is an example of the manner in which a nearly square mass, so designed for structural reasons, may, by Rules 3b and 2a, be broken into a fairly pleasing arrangement of divisions.
More Than Three Divisions
Rule 3c. In elementary problems, if more than three vertical divisions are required, they should be so grouped as to analyze into Rules 3a and 3b, or be exactly similar. The eye becomes confused by a multitude of vertical divisions and it is much better designing to keep them within the number stated in this chapter. There are instances, however, when this is impossible. Under such conditions the following treatment should be adopted:
Unless, as stated, a large number of vertical divisions may be grouped into two or three vertical divisions it is better to make all of the divisions of the same size. This does not fatigue the eye as much as would the introduction of a number of complex spacings. This solution enables the amateur designer to deal with complex problems with an assurance of securing a degree of unity.
INSTRUCTION SHEET
[Plate 15] is practically self-explanatory and shows the order in which the various divisions, so far considered, are to be introduced into the design together with the grouping of details within those divisions. Figure D introduces the additional element termed the appendage to be considered in [Chapter V].
SUMMARY OF DESIGN STEPS
(a) Construction of the rectangle representing the vertical or horizontal character of the primary mass with desirable proportions. Select the most prominent surface for this rectangle, preferably the front elevation.
(b) Subdivide this rectangle into two or three structural sections, horizontal and vertical in character. Make two or three trial freehand sketches on cross section paper for varied proportions and select the most pleasing in accordance with rules.
(c) Translate the selected sketch into a scale or full size drawing and add additional views to complete the requirements of a working drawing. Add additional structural elements: legs, rails, etc.
(d) For shop purposes, enlarge a scale drawing to full size, dimension and otherwise prepare it for actual use. See [Figure 102a], [page 68], for character of this change.
(e) Construct the project.
SUGGESTED PROBLEMS
Design a fire screen with two horizontal and three vertical major subdivisions.
Design a bookcase 4 feet 2 inches high with three horizontal and two vertical major subdivisions.
SUMMARY OF RULES
Rule 3a. If the primary mass is divided into two vertical divisions, the divisions should be equal in area and similar in form.
Rule 3b. If the primary mass is divided into three vertical divisions, the center division should be the larger, with the remaining divisions of equal size.
Rule 3c. In elementary problems, if more than three vertical divisions are required, they should be so grouped as to analyze into Rules 3a and 3b, or be exactly similar.
REVIEW QUESTIONS
1. What is the nature and need of vertical space divisions?
2. State the rule governing the use of two vertical space divisions and give illustrations in wood, clay, and metal.
3. Give the rule relating to the use of three vertical space divisions and furnish illustrations in wood, clay, and metal.
4. What is the treatment of more than three vertical divisions? Why?
Chapter V
APPENDAGES AND RULES GOVERNING THEM
Use of the Appendage
An appendage is a member added to the primary mass for utilitarian purposes. In the industrial arts, when an appendage is added merely for the purpose of decoration, it is as useless and functionless as the human appendix and, as a source of discord, should be removed.
An appendage in industrial arts may be, among other things, a plate rail, bracket, spout, cover, or handle, all of which are capable of service either for or with the primary mass. In architecture it may be a wing or ell added to the mass of the building. Simple as its design may seem, it is often so placed in relation to the main or primary mass that it does not seem to "fit" or to be in unity with that mass.
Designing an Appendage
Rule 4a. The appendage should be designed in unity with, and proportionately related to, the vertical or horizontal character of the primary mass, but subordinated to it.
Rule 4b. The appendage should have the appearance of flowing smoothly and, if possible, tangentially from the primary mass.
Rule 4c. The appendage should, if possible, echo or repeat some lines similar in character and direction to those of the primary mass.
Violations of Appendage Design
All of the foregoing rules are intended to promote the sense of unity between the primary mass and its appendages. If a mirror on a dresser looks top-heavy it is generally due to the fact that it has not been subordinated in size to the primary mass. Rule 4a. If the handle projects from the primary mass of an object similar to the handle on a pump, it has not been designed in accordance with Rules 4b and 4c. Again, if the appendage projects from a primary mass like a tall chimney from a long flat building, it has violated Rule 4a and has not been proportionately related to the character of the vertical or horizontal proportions of the primary mass.
Plate 16
It should be readily seen that if the primary mass has one dominant proportion while the appendage has another, there will be a serious clash and the final result will be the neutralization of both motives, resulting in either an insipid and characterless design or a downright lack of unity.
Appendages in Wood
The design of the small dressing table, [Figure 37], [Plate 16], with the mirror classing as an appendage, is an excellent illustration of Rule 4a. The main mass of the table is vertical in character and the mirror carries out or repeats the character of the primary mass by having a similar but subordinate vertical mass. In this instance it is so large that it has nearly the effect of a second primary mass.
As tangential junctions are difficult to arrange in wood construction and particularly in furniture, the break between the table top and the mirror has been softened by the introduction of a bracket or connecting link. The curves of the link cause the eye to move freely from the primary mass to the appendage and thus there is a sense of oneness or unity between the two masses.
The lantern in [Figure 38] becomes an appendage and is subordinated to the large pedestal or support. The tangential junction has in this case been fully possible and the eye moves freely from the vertical lines of the base to the similar vertical mass of the lantern without noticeable break.
Unifying Appendage and Primary Mass
The service of the dressing table, [Figure 39], with its three-division mirror makes the problem of adaptation of the appendage to the mass of the table, in accordance with the rules, much more difficult. Under the circumstances, about the best that can be done, at the same time keeping within the limitations of desired service, is to plan the mirrors in accordance with Rule 3b, with the dominant section in the center. To secure an approach to unity, each section of the mirror should echo the vertical proportion of the primary mass of the table.
Courtesy of Berkey and Gay
Figure 41a
The top of the writing stand, in [Figure 40], is an example of a horizontal appendage which repeats the horizontal character of the front or typical face of the primary mass of the table. The small drawers and divisions again take up and repeat the horizontal motive of the table, while the entire appendage may be subdivided under Rule 3b, giving the dominance to the center portion. The short curves in the appendage all tend to lead the eye in a satisfactory and smooth transition from one mass to the other or from the table top to the appendage. The proportions of the small drawers are similar to the proportions of the table drawers. Rule 4c. All of these points of similarity bring the masses into close unity or oneness of appearance.
The table legs, in [Figure 41], are more difficult to adjust satisfactorily. The idea of the designer is, however, apparent. The legs leave the column of the table with a tangential curve and, sweeping out with a strong curve, repeat the horizontal line of the table top in the horizontal lines of their bottom surfaces.
Industrial Applications
[Figure 41a], a modification of [Figure 39], shows close unity between the three divisions of the mirror due to the pleasing curve of the center section with its tendency to bind the other sections to it. Again, the echoing of the spacings of the three drawers in the similar spacings of the three mirrors, makes the bond of unity still closer to the ideal arrangement. Rule 4c.
[Figures 41b] and [41c] are, in a way, parallel to [Figure 41]. The eye moves freely from the feet (appendages) along the smooth and graceful curves to the tall shaft or column of the primary mass. The turned fillets, introduced at the junction of the appendage and the primary mass, in [Figure 41c], have a tendency to check this smooth passage making the arrangement in [Figure 41b] preferable. The hardware for the costumers is well chosen and in sympathy with the vertical proportions of the design.
Courtesy of Berkey and Gay
Figure 41b Figure 41c
Appendages in Clay
With the word "clay" all difficulties in the treatment of appendages vanish. It is by far the easiest medium for the adaptation of the appendage to the primary mass. Covers, handles, and spouts are a few of the more prominent parts falling under this classification.
The process of the designer is to create the primary rectangle, subdivide it into two horizontal subdivisions in accordance with Rule 2a, and proceed to add the desired number of appendages. The result may be suggested by the following illustrations. In [Figure 43], [Plate 17], the cover is a continuation of the curve of the top of the bowl, Rule 4a; the tops of the handles are continuations of the horizontal line in the top contour of the bowl, while the lower portions of the handles seem to spring or grow from the lower part of the bowl with a tangential curve.
Covers, Spouts, and Handles
[Figure 44] is a horizontal primary mass with the horizontal subdivision in the upper section of that mass. The spout and handle spring naturally from the body and balance each other in proportion, while the cover handle rises smoothly from the primary mass. The horizontal character of the primary mass is consistently carried out in the appendages.
The handle, in [Figure 45], leaving the body at a tangent, rises with a long straight curve to turn suddenly and join the pitcher in harmony with its top. The apparent abruptness of the junction is softened by the rounded corners typical of clay construction.
The Rookwood set, [Figure 42], represents three similar primary masses. The proportionate ratios and the horizontal subdivisions are the same throughout. The handle for the teapot has been curved in the center to give variety to the handle. This variation is a difficult thing to manage without consequent loss of unity as by this variation Rule 4a is violated. One thing may be said in its favor. It brings the hand closer to the spout and thus supports the pouring weight. But the unusual in design is to be discouraged until sufficient skill in simple designing has been acquired.
In designing handle appendages for clay, they should be so placed that they readily control the weight of the material in the container and afford room for the fingers. Thus, it is better to have the larger portion of the handle opening at the top of the primary mass. The spout in all instances should continue sufficiently high to allow the container to be filled to its full capacity without danger of the contents running out of the spout. The glaze runs into rounded corners much more freely than into square ones, hence it is preferable to use rounded corners wherever possible.
Plate 17
Requirements for Appendage Design
Freehand Curves
It is the unexpected curve that is welcome in all designing, provided it supports the structure and conforms to established rules. After completing a design involving appendages it should be checked from three points of view; (1) service, (2) unity between the primary mass and the appendages, and (3) variety of curvature. On this last point it is needless to say that compass curves are not desirable except in rounding small corners or in using fillets. It is well known that compass curves are difficult to assimilate into pleasing tangential effects. They are inclined to be monotonous and regular with a "made by the thousand" appearance to them. One should trust to freehand sweeps, drawn freely with a full arm movement when possible. All curves should spring naturally from the primary mass. Blackboard drawing is excellent practice for the muscles used in this type of designing. In a short time it will be found possible to produce the useful long, rather flat curve with its sudden turn (the curve of force) that will make the compass curve tame and commonplace by comparison.
Appendages in Metal
[Figures 55], [56], and [57], [Plate 18], show the close bond between the appearance of the appendage in clay, and the one in metal. While it is technically more difficult to adapt metal to the rules governing appendages than is the case with clay, the final results are, in most instances, equally pleasing to the eye.
In most of the figures showing examples in metal, the appendages have to be secured to the primary mass by screws, rivets, or solder, whereas in clay they may be moulded into the primary mass. This tends to secure a more unified appearance; but in metal, the junction of the handle and the primary mass is often made a decorative feature of the design and gives added interest and variety to the project.
The simple primary mass, [Figure 58], has a horizontal space division in the lower portion of the mass. This point of variation of the contour has been used in the primary masses in [Figures 55], [56], and [57], also as the starting point of that dominant appendage, the handle. Springing tangentially from the body, it rises in a straight line of extreme value in service, then with a slight turn it parallels and joins the top of the bowl, thus fulfilling the design functions of an appendage from both points of service and beauty. The spout and lid, [Figure 55], may be likewise analyzed.
Plate 18
Tangential Junctions
The points of tangency, in [Figure 54], become a decorative feature of the design. The handles in the parts of the fire set, [Figures 48] and [49], offer different problems. It is difficult to analyze the latter figures to determine the appendages as they are in such thorough unity with the handles and are practically subdivisions of the primary mass. But referring to the rule stating the fact that the appendages are subordinated to and attached to the primary mass, it may justly be stated that the shovel portion of the design may legitimately be classed as an appendage. This will explain the need of a curve at the junction points and the feature of the decorative twists in [Figure 49]. Both designs may be analyzed into three horizontal divisions.
Andiron Design
The andirons, [Figures 50] to [53], illustrate interesting transitions in wrought iron from the primary mass to the appendage. The vertical shaft of wrought iron has been treated as a primary mass while the feet may be classed as appendages. In [Figure 50] we have an example of a frankly square junction point. [Figure 51] discloses a weld with rounded corners, forming a more pleasing junction than does the abrupt angle of [Figure 50]. This conforms to Rule 4b. The appendage legs echo or repeat the vertical lines of the primary mass and there is consequently a sense of unity between them.
In [Figure 52] the appendage foot is curved, and the primary mass has a similar curve on the top of the vertical column to apply Rule 4c to repeat the curve. The small links at X indicate an attempt to make the junction point more pleasing to the eye, but the link is too large to accomplish the desired result successfully. In [Figure 53] the links have been materially reduced in size and in the amount of curvature. In this example the eye goes unhampered from appendage to primary or back again, without perceptible interruption and the unity of the mass, seriously threatened in [Figure 52], is restored in [Figure 53].
In [Figure 46] there is an example of a link becoming large enough to be classed as an appendage connecting two primary masses, e.g., the lantern and the wall. Under these conditions, one end of the appendage harmonizes with the lantern and the other end with the wall. [Figure 47] shows a cast brass candlestick which is an excellent example, from the Studio, of tangential junction.
Influence of Tools and Materials
Clay may readily stand as the most adaptable material for appendages, with metal ranking second, and wood third. The grain of wood seems to interfere with the tangential junction of the appendage and primary mass. Appendages of wood are, however, quite necessary at times. Their use is merely a matter of lessening the contrast of conflicting lines in an addition of this nature.
The band and bracket saws are required in many instances to construct the connecting link between opposing masses of wood. Hand building or casting is the means used to construct the appendages in plastic materials. Appendages in cement are seen in the uprights for cement seats and are generally translated into the primary mass by means of mouldings or curves.
Forging or thin and raised metal construction affords many examples of the adaptability of material in constructing appendages. Rivets form decorative features at the junction points and should be placed with great care and relation to the decoration and the point of tangency.
Plate 19
INSTRUCTION SHEET FOR CLASS PRESENTATION
The typical views to be used in classroom work, with the ordinary range of problems, are shown on [Plate 19]. These typical views should be supplemented by dimensions, cross sections, and other views whenever necessary. Wood construction has been omitted from this sheet, but its development in design is quite similar to the steps indicated in the summary.
SUMMARY OF DESIGN STEPS
(a) Draw the primary rectangle.
(b) Subdivide the rectangle into two or three horizontal and, if necessary, vertical divisions.
(c) Estimate the dimensions of the appendage necessary to perform the desired service in the best manner.
(d) If the appendage is a handle, place it in such a position that it not only appears to but actually does support the weight of the primary mass.
(e) Complete the contour curves of the primary mass based upon the horizontal division which acts as a unit of measurement or a turning point.
(f) Join the appendages to the primary mass by means of tangential curves.
(g) Establish unity between the primary mass and the appendages by applying Rules 4a, 4b, and 4c.
(h) Dimension and otherwise prepare the drawing for shop use. See [Plate 26].
SUGGESTED PROBLEMS
Design a sugar bowl, cream pitcher, and teapot. Consider them as different members of one set.
Design a sideboard 3 feet 3 inches high with plate rack, the design to contain two vertical and two horizontal divisions exclusive of the appendage.
SUMMARY OF RULES
Rule 4a. The appendage should be designed in unity with, and proportionately related to, the vertical or horizontal character of the primary mass, but subordinated to it.
Rule 4b. The appendage should have the appearance of flowing smoothly and, if possible, tangentially from the primary mass.
Rule 4c. The appendage should, if possible, echo or repeat some lines similar in character and direction to those of the primary mass.
REVIEW QUESTIONS
1. State the nature and use of the appendage.
2. What is the relation of the size of the appendage to the size of the primary mass?
3. How should the appendage be attached to the primary mass?
4. How does Rule 4c help to secure unity between the appendage and the primary mass?
5. Are compass curves permissible in appendage design?
6. State influence of tools and materials upon appendage design.
Chapter VI
ENRICHMENT OF THE CONTOURS OR OUTLINES OF DESIGNS IN WOOD
With this chapter we introduce contour enrichment, the second major division of industrial arts design.
Need and Value of Enrichment
A critic of furniture designed by the average manual arts student has stated frankly that while it might have been honestly constructed it was, in the first place, too heavy for a woman to move about the house and, in the second place, it represented a decidedly uneconomical use of that valuable material, wood. That there is a basis in fact for this statement cannot be denied. Is it true, then, that furniture must of necessity be clumsy and heavy when it is sufficiently simplified in constructive processes for school work? We may say emphatically, "No!"
One may correct the proportions of an object and reduce the size of the materials in it to a minimum but still fail to secure the desirable elements of lightness and interest. The object may still look heavy and remain a box-like structure void of the grace synonymous with the best in design. It is, however, possible to correct the clumsy and heavy appearances by imparting to the design elements of grace and lightness. Two methods may be used, singly or together: (1) Enrichment of the Functional Outlines or Contours; (2) Surface Enrichment sometimes called Space Filling. These may be roughly classified respectively as three and two dimension enrichment.
Contour Enrichment
The first, or outline enrichment, concerns itself with the structural lines. As all designing processes should start with the structure, it will be our policy to do so. The present chapter will deal only with enrichment of outlines of wood projects.
Rule 5a. Outline enrichment should be subordinated to and support the structure.
Rule 5b. Outline enrichment should add grace, lightness, and variety to the design.
Plate 19a
Purpose of Contour Enrichment
It is the purpose of enrichment to add to the problem (1) grace; (2) lightness; (3) variety; (4) unity. If it is applied in a proper manner it should likewise add to the apparent structural strength. We should carefully guard the design, therefore, against (1) enrichment that has a tendency to obscure or destroy the structural lines; in other words, enrichment that is not subordinated to the structure, and (2) enrichment that adds nothing to the structure by its application; that is, one which does not increase either the apparent strength or the beauty of the object.
Requirements of Contour Enrichment
As an example of this first point, the turned candlestick with the candle supported by a stack of turned balls alternating with tauri or thin discs tends to obscure completely the sense of support. Again, the landscape gardener feels that he is violating a fundamental principle in design if by planting vines to grow around a building, he obscures the foundation, and the roof appears, consequently, to rest on and be supported by the stems and leaves of the vines. Thus it is seen that the eye registers a sense of structural weakness when the main supports of an object disappear and are no longer to be traced under the enrichment.
Under the second point falls the indiscriminate placing of unrelated objects in the contour enrichment. Naturalistic objects similar to the claw foot and the human head, for example, should give way to natural curves that add to the appearance of total strength. Where are we to find these curves suited to our purpose?
Valuable Curves for Outline Enrichment
Up to this point emphasis has been placed upon straight and curved lines immediately connected with pure service. For grace and lightness it is necessary to depart at times from the rigidity of straight lines. To understand the character of this departure let us consider a simple bracket as a support for a shelf.
This bracket acts as a link, connecting a vertical wall or leg with a horizontal member or shelf. A bracket shaped like a 45-degree triangle, [Figure 10], [page 24], gives one the sense of clumsiness. If the feeling of grace is to be imparted the eye must move smoothly along the outline of the bracket, giving one a sensation of aesthetic pleasure. A curved line will produce this effect more completely than will a straight line. One must likewise get the feeling that the curve of the bracket is designed to support the shelf.
Plate 20