List No. VII
| 61. | What adjustments are there for the second elevator? | |
| 62. | What would cause the second elevator to be held at the | |
| distributor? | ||
| 63. | When the second elevator does not descend, what causes | |
| the machine to stop? | ||
| 64. | Give the adjustments of the elevator transfer slide. | |
| 65. | What is the releasing lever for in the first elevator slide | |
| guide, and how is it adjusted? | ||
| 66. | What is the object of the intermediate bar pawl? | |
| 67. | How may the movement of the transfer and spaceband | |
| levers be interfered with? | ||
| 68. | How does locking the spaceband transfer lever stop the | |
| machine? | ||
| 69. | How does the spaceband transfer lever get its motion | |
| and how is it adjusted? | ||
| 70. | When does the automatic safety pawl act? | |
List No. VIII
| 71. | Describe the method and order that should be followed | |
| in making a complete change of the machine from | ||
| one size to another. | ||
| 72. | How are the mold liners marked to distinguish size? | |
| 73. | How is the ejector blade held in place? | |
| 74. | What will cause a slug to be pushed out of a galley | |
| when being ejected? | ||
| 75. | What is the purpose of the buffer spring in the ejector | |
| slide? | ||
| 76. | What is the ejector-blade guide for, and what care does | |
| it require? | ||
| 77. | What makes a slug higher on one end than on the other? | |
| 78. | How is the back knife adjusted? Explain in detail. | |
| 79. | How is a micrometer read? | |
| 80. | What is “type high”? | |
List No. IX
| 81. | Explain in detail how the trimming knives are adjusted. | |
| 82. | What causes slugs to be off their feet, or lift, when | |
| locking-up? | ||
| 83. | What part of an inch is a type founders point? What | |
| part of an inch is a linotype point? | ||
| 84. | How are the decimal points of a slug found? | |
| 85. | When can the vise be opened to first position? | |
| 86. | When can the vise be opened to second position? | |
| 87. | Explain the construction of the main friction clutch. | |
| 88. | How is the collar connected to the clutch rod? | |
| 89. | What is the difference between the new and the old | |
| style clutch adjustment? | ||
| 90. | How is the main driving clutch adjusted? Give the | |
| seven adjustments affecting the clutch. | ||
List No. X
| 91. | In what position should the starting lever be when | |
| making the adjustments on the friction clutch? | ||
| 92. | What care should be given to the main friction clutch? | |
| 93. | How can you determine when the clutch is slipping? | |
| 94. | Give causes for the slipping of the clutch, and how | |
| you would remedy them. | ||
| 95. | What is the action of the automatic safety pawl when | |
| striking the upper stopping lever, and how does it | ||
| effect the clutch to stop the machine? | ||
| 96. | State the purpose of the vise automatic, and tell how | |
| it is adjusted. | ||
| 97. | How is the vise automatic adjustment tested? | |
| 98. | How are the matrix toes sheared when the vise automatic | |
| is out of adjustment? | ||
| 99. | How is the mold slide adjusted? Give all adjustments. | |
| 100. | Describe the machine action from the time a line is in | |
| the assembling elevator until it has been distributed. | ||