Painting by Immersion and by Compressed Air: A Practical Handbook

by Arthur Seymour Jennings

Fig. 31.—Dipping Casements at the Crittall Manufacturing Co.'s Factory, Braintree.

Perhaps the most noticeable feature of these works as far as our subject is concerned, is the very complete system of overhead rails, by means of which the various metal goods produced in the different finishing shops are conveyed to one or other of the paint tanks and then, having been left to dry, are taken to store rooms ready for instant shipment. These rails facilitate handling of the various goods, and reduce the actual expenditure under this particular item to a minimum. The rails are L-shaped, the hanger used for each article or series of articles being of a simple character, consisting of two wheels bearing on the top of the upright flange, while rods secured by bolts pass through the horizontal flange and hold it in position.

We will first describe the tank used for dipping metal windows. This is 15ft. long by 12ft. deep and only 1ft. 6in. wide. Attached to the tank is a large dripping floor measuring some 15ft. by 21ft. covered with sheet iron and inclined toward the tank, so that the paint which drips on to it finds its way back into the tank through a grating provided for the purpose to take off any dried particles. The paint used in this work is made by Messrs. Docker Brothers, and weighs 13 lbs. to the gallon; one coat is found sufficient for the purpose. The sashes or casements being brought in from the finishing room on the overhead rail, they are lowered into the tank by means of a special lowering apparatus designed on the premises. Some idea of this may be had from Fig. 31. In order to keep the load steady during the time it is being dipped, a slight depression or dip in the rail is made immediately over the tank. The sashes are only left in the paint for a few seconds, and are then raised, allowed to drip over the tank for perhaps a minute or two, and then allowed to drip over the adjacent floor for perhaps a quarter of an hour or less. They are then taken farther along and the paint dries in about three hours. Sometimes two, four, six, or even eight casements may be dipped at the same time. Attached to the elevating and lowering apparatus are hooks which pass through one corner of the casements. This causes the parts to hang at an angle which facilitates running off of the paint.

We come now to the department in which the baking or stoving enamel is used as applied to metal furniture in general, as mentioned. In this case the articles are dipped in a manner very similar to that already described, excepting that a large hook, similar in shape to that shown in Fig. 32, is used to support the article to be dipped; the wide opening goes inside the box or file and holds it at an angle so that when it is lowered into the paint all parts are covered inside and out. A few minutes are allowed for dripping, and after two or three hours the articles are ready to be stoved. In this case, Messrs. Docker Brothers' standard colour, a very pleasing dark green, is used. The stoving takes three hours at a temperature of 240° F., or higher in some cases. The tank mentioned is, of course, considerably wider than that used for casements. The dripping floor is in this case inclined toward the centre, which in turn is inclined toward the grating just outside the tank itself. If necessary, special thinners are added to bring up the gloss, but, as a rule, this is unnecessary. It is desirable after the article is dipped to go over it once with a small brush to remove any drips or runs which may possibly appear.

Fig. 32.—Hook Used for Suspending Metal Boxes While Dipping.

Another very important point to be attended to is to exclude all dust, and for this purpose the Crittall Manufacturing Co. have erected in this department screens of wire of the finest mesh over windows, so that no air can pass into the room without the dust being screened off.

Excluding Dust.

A matter of very great importance, yet one which is frequently overlooked in painting iron and other goods which are to have a glossy finish, either air dried or stoved, is to exclude dust from the apartment in which the work is done. In many engineering shops the nature of the business gives rise to a considerable amount of dust, and if this is allowed to enter the paint shop it will be fatal to the appearance of the painted work, as many specks will inevitably settle on the work and mar its appearance.