Every-day Science: Volume 6. The Conquest of Nature

by Henry Smith Williams; Edward Huntington Williams

"(f) The fly-wheel now continues running freely till its speed, as determined by a centrifugal governor, falls below a certain limit when a trip gear causes the piston to be lifted the short distance required to recommence the cycle.

"Ignition is performed by an external gas jet, near a pocket in the slide valve by which the charge is admitted; this pocket carries flame to the charge, thus igniting it without allowing any escape. The valve also connects the interior of the cylinder with the exhaust pipe, and a valve in the latter controlled by the governor throttles the discharge, and so defers the next stroke until the speed has fallen below normal. To run the engine empty about four explosions per minute are necessary, and at full power 30 to 35 are made, so that about 28 explosions per minute are available for useful work under the control of the governor."

The definitive improvement in this gas engine was introduced in 1876 by Dr. N. A. Otto, when he compressed the explosive mixture in the working cylinder before igniting it. This expedient—so all-important in its results—had been suggested by William Barnett in 1838, but at that time gas engines were not sufficiently developed to make use of the idea. Now, however, Dr. Otto demonstrated that by compressing the gas before exploding it a much more diluted mixture can be fired, and that this gives a quieter explosion, and a more sustained pressure during the working stroke, while as the engine runs at a high speed the fly-wheel action is generally sufficient to correct the fluctuations arising from there being but one explosion for four strokes of the piston.

In this perfected engine, then, the method of operation is as follows:

The piston is pulled forward with the application of some outside force, which in practice is supplied by the inertia of the fly-wheel, or in starting the engine by the action of a crank with which every user of an automobile is familiar. In being pulled forward, the piston draws gas into the cylinder; as the piston returns, this gas is compressed; the compressed gas, constituting an explosive mixture, is then ignited by a piece of incandescent metal or by an electric spark; the exploding gas expands, pushing the piston forward, this being the only thrust during which work is done; the returning piston expels the expanded gas, completing the cycle. Thus there are three ineffective piston thrusts to one effective thrust. Nevertheless, the engine has proved a useful one for many purposes.

This so-called Otto cycle has been adopted in almost all gas and oil engines, the later improvements being in the direction of still higher compression, and in the substitution of lift for slide valves. There has been a steady increase in the size and power of such engines, the large ones usually introducing two or more working cylinders so as to secure uniform driving. Cheap forms of gas have been employed such as those made by decomposing water by incandescent fuel, and it has been proved possible thus to operate gas-power plants on a commercial scale in competition with the most economical steam installations.

A practical modification of vast importance was introduced when it was suggested that a volatile oil be employed to supply the gas for operation in an internal combustion engine. There was no new principle involved in this idea, and the Otto cycle was still employed as before; but the use of the volatile oil—either a petroleum product or alcohol—made possible the compact portable engine with which everyone is nowadays familiar through its use in automobiles and motor boats. The oil commonly used is gasoline which is supplied to the cylinder through a so-called carburettor in which the vapors of gasoline are combined with ordinary air to make an explosive mixture. The introduction of this now familiar type of motor is to a large extent due to Herr G. Daimler, who in 1884 brought out a light and compact high-speed oil engine. About ten years later Messrs. Panhard and Levassor devised the form of motor which has since been generally adopted. Few other forms of mechanisms are better known to the general public than the oil engine with its two, four, six, or even eight cylinders, as used in the modern automobile. As everyone is aware, it furnishes the favorite type of motor, combining extraordinary power with relative lightness, and making it feasible to carry fuel for a long journey in a receptacle of small compass.

With the gas engines a complication arises precisely opposite to that which is met with in the case of the cylinder of the steam engine—the tendency, namely, to overheating of the cylinder. To obviate this it is customary to have the cylinder surrounded by a water jacket, though air cooling is used in certain types of machines. About fifty per cent. of the total heat otherwise available is lost through this unavoidable expedient.

The rapid introduction of the gas engine in recent years suggests that this type of engine may have a most important future. It has even been predicted that within a few years most trans-Atlantic steamers will be equipped with this type of engine, producing their own gas in transit. It is possible, then, that through this medium the old piston-and-cylinder engine may retain its supremacy, as against the turbine. For the moment, at any rate, the gas engine is gaining popularity, not merely in its application to the automobile, but for numerous types of small stationary engines as well.