Let F be the stiffness in pounds avoirdupois; d the diameter of the rope in inches, n = 48d2 for white ropes and 35d2 for tarred ropes; r the effective radius of the pulley in inches; T the tension in pounds. Then
| For white ropes, F = | n | (0.0012 + 0.001026n + 0.0012T). |
| r |
| For tarred ropes, F = | n | (0.006 + 0.001392n + 0.00168T). |
| r |
(68)
§ 105. Friction-Couplings.—Friction is useful as a means of communicating motion where sudden changes either of force or velocity take place, because, being limited in amount, it may be so adjusted as to limit the forces which strain the pieces of the mechanism within the bounds of safety. Amongst contrivances for effecting this object are friction-cones. A rotating shaft carries upon a cylindrical portion of its figure a wheel or pulley turning loosely on it, and consequently capable of remaining at rest when the shaft is in motion. This pulley has fixed to one side, and concentric with it, a short frustum of a hollow cone. At a small distance from the pulley the shaft carries a short frustum of a solid cone accurately turned to fit the hollow cone. This frustum is made always to turn along with the shaft by being fitted on a square portion of it, or by means of a rib and groove, or otherwise, but is capable of a slight longitudinal motion, so as to be pressed into, or withdrawn from, the hollow cone by means of a lever. When the cones are pressed together or engaged, their friction causes the pulley to rotate along with the shaft; when they are disengaged, the pulley is free to stand still. The angle made by the sides of the cones with the axis should not be less than the angle of repose. In the friction-clutch, a pulley loose on a shaft has a hoop or gland made to embrace it more or less tightly by means of a screw; this hoop has short projecting arms or ears. A fork or clutch rotates along with the shaft, and is capable of being moved longitudinally by a handle. When the clutch is moved towards the hoop, its arms catch those of the hoop, and cause the hoop to rotate and to communicate its rotation to the pulley by friction. There are many other contrivances of the same class, but the two just mentioned may serve for examples.
§ 106. Heat of Friction: Unguents.—The work lost in friction is employed in producing heat. This fact is very obvious, and has been known from a remote period; but the exact determination of the proportion of the work lost to the heat produced, and the experimental proof that that proportion is the same under all circumstances and with all materials, solid, liquid and gaseous, are comparatively recent achievements of J. P. Joule. The quantity of work which produces a British unit of heat (or so much heat as elevates the temperature of one pound of pure water, at or near ordinary atmospheric temperatures, by 1° F.) is 772 foot-pounds. This constant, now designated as “Joule’s equivalent,” is the principal experimental datum of the science of thermodynamics.
A more recent determination (Phil. Trans., 1897), by Osborne Reynolds and W. M. Moorby, gives 778 as the mean value of Joule’s equivalent through the range of 32° to 212° F. See also the papers of Rowland in the Proc. Amer. Acad. (1879), and Griffiths, Phil. Trans. (1893).
The heat produced by friction, when moderate in amount, is useful in softening and liquefying thick unguents; but when excessive it is prejudicial, by decomposing the unguents, and sometimes even by softening the metal of the bearings, and raising their temperature so high as to set fire to neighbouring combustible matters.
Excessive heating is prevented by a constant and copious supply of a good unguent. The elevation of temperature produced by the friction of a journal is sometimes used as an experimental test of the quality of unguents. For modern methods of forced lubrication see [Bearings].
§ 107. Rolling Resistance.—By the rolling of two surfaces over each other without sliding a resistance is caused which is called sometimes “rolling friction,” but more correctly rolling resistance. It is of the nature of a couple, resisting rotation. Its moment is found by multiplying the normal pressure between the rolling surfaces by an arm, whose length depends on the nature of the rolling surfaces, and the work lost in a unit of time in overcoming it is the product of its moment by the angular velocity of the rolling surfaces relatively to each other. The following are approximate values of the arm in decimals of a foot:—