Supposing that some arrangement of this sort is devised, we must unpack some bromide paper and put it in its box and then put a negative of "average" density in an ordinary printing frame. On the film side of the negative we must now place a sheet of bromide paper with its sensitive side in contact, replace the back of the frame and it is ready for exposure. Before exposing it, make sure that both boxes are shut or their contents will be ruined the moment the white light is turned up.
Upon reference to the instructions that accompany each packet of bromide paper, you will observe a certain number of seconds' exposure is advised at a certain distance from the light; in the case of the Barnet extra rapid paper the time is given as about four seconds at a distance of eighteen inches.
When all is ready for exposure, place the printing frame upright opposite the lantern at the mark indicating eighteen inches (see [fig. 2]), note the time on the seconds hand of the clock and throw the lever over for white light for four seconds and then reverse it. Remove the paper and if many are likely to be required from that negative, it would be well to develop the first print in order to judge as to the accuracy of the exposure. If over or under-exposed, the time must be reduced or lengthened as required. When the best time and distance has been ascertained for a certain negative, mark it with a narrow strip of paper bearing full particulars for future guidance, such as: "4 sec., 18 in., No. 5 Bray;" in this way absolute correctness of future exposures is assured. Of course, if gas is not obtainable, magnesium ribbon may be used instead. In this case the negative would be marked "1 inch (or more) ribbon, 3 ft. distant," as the case may be.
Using Masks and Discs.—Prints are sometimes required with an oval (or square) centre and white margins: this is effected by interposing a black mask of the desired size and shape (obtainable from all dealers) between the negative and the sensitive paper. The black paper prevents the passage of light and leaves white margins to the print. If grey margins are required, a disc (to fit the mask) is attached to a sheet of glass the same size as the negative and arranged so that registration is easily effected; the print is first made with a mask and is then placed in contact with the disc and plain glass (the negative being removed from the frame), and again exposed for a second to the light. If a black border is required the exposure of the margin must be extended three or four seconds.
Vignetting.—To vignette bromide prints, the printing frame must be covered with a piece of cardboard in which a small hole (about 1½ inches by 1 inch for a cabinet head and bust) is pierced. The hole must be covered with a sheet of white tissue paper which will diffuse the light and cause it to travel without harsh lines beneath the opening, and make the print with perfectly gradated edges. It is sometimes an advantage to move the negative while printing vignettes; but it is not absolutely essential if the hole in the cardboard is not too large and if the card is removed some little distance from the negative. If the card is too close to the negative, the gradation will be abrupt and the vignette will not look well.
Cloud Printing.—This requires some care in order to avoid harshness and sharply defined lines. If the sky of the negative prints white, the addition of clouds from another negative is not difficult; but if it is at all thin, the entire sky must be carefully painted out with a deeply opaque pigment in order to make it quite dense and unprintable.
As a bromide print cannot be examined while in progress: that is, cannot be seen at all before development, careful registration is desirable in order to prevent printing the clouds across the landscape instead of above it. To do this an opaque mask should be made thus: Make a print from the negative on P.O.P. and, without fixing or toning it, cut it carefully in two parts following the horizon line as nearly as possible, then expose to light, until quite black, that part representing the landscape. Attach this to the glass side of the cloud negative (with the paper side of the P.O.P. in contact) and see that the bottom edge and the right corner of the paper and glass (viewed from the glass side of the negative) exactly coincide. To make use of this arrangement, you first make a print from the landscape negative, making sure that the negative and paper are firmly pressed against the bottom and left-hand side of the printing frame when looking towards the film side of the negative; mark the registered corner with lead pencil thus =L= in order to prevent mistakes in the second printing.
To print the clouds, you put the negative in the frame and press it well home to the left-hand corner and the base of frame (looking at the film side, of course), and then put the print in contact with the same precaution and replace the back. Now take a piece of brown paper with one edge roughly torn in shape of the horizon line of the mask and cover the entire negative on the glass side. Hold the covered frame in your hands at a distance of (say) four feet from the gas and turn on the white light. Directly the light is up, draw the paper slowly downwards until the horizon line is just passed, and then immediately begin to slowly push it upwards towards the top of the sky. Do this steadily and slowly for (say) four to six seconds, according to the density of the cloud negative. With a good thin cloud, four seconds should be quite enough, but you can easily settle this point on developing the first print.
Printing from Dense Negatives.—Dense negatives require much longer exposures than those of "average" (or ideal) density. This may often be prolonged to twice or three times the normal exposure at the same distance. A yellow coloured negative increases the exposure greatly, as much as ten to thirty times the normal frequently being requisite to get a decent print. An over dense negative that gives very harsh prints by other printing processes can be made to yield prints of exquisite softness on bromide paper by giving a full exposure at a short distance from the gas.