Twentieth Century Inventions: A Forecast

by George Sutherland

One promising use of the turbine or steam-jet—used to propel a fly-wheel filled with liquid as described—has for its object the supply of the electric light in country houses. In this case the fly-wheel is fitted, on its lower side, to act as the armature of a dynamo, and the magnets are placed horizontally around it.

The full effective power from a jet of steam is not communicated to a dynamo for electric lighting or other purposes unless there be a definite ratio between the speeds of the turbine and of the armature respectively. This may be conveniently provided for, with more precision and in a less elaborate way than that which has just been described, if the steam jet be made to drive a vertically pendant turbine, the lower extremity of which, carrying very small horizontal paddles, must be inserted into the centre of a circular tank.

The principle upon which the reduction of speed necessary for the dynamo is then effected depends upon the fact that in a whirlpool the liquid near the centre runs nearly as fast as that on the outer periphery, and therefore—the circles being so very much smaller—the number of revolutions effected in a given time is much greater. Thus a steam jet turning a pendant turbine—dipping into the middle of the whirlpool and carrying paddles—at an enormously high speed may be made to impart motion to the water in a circular tank (or, if desired, to the tank itself) at a very much slower rate; the amount of the reduction, of course, depending mainly on the ratio between the diameter of the tank and the length of the small paddles at the centre setting the liquid in motion.

For special purposes it is best to substitute a spherical for an ordinary circular tank and the size may be greatly diminished by using mercury instead of water. The sphere is complete, excepting for a small aperture at the top for the admission of the steel shaft of the steam-driven turbine. No matter how high may be the speed, the liquid cannot be thrown out from a spherical revolving receptacle constructed in this way. Moreover, the mercury acts not only as a transmitter of the power from the turbine to the purpose for which it is wanted, but also as a governor. Whenever the speed becomes so great as to throw the liquid entirely into the sides of the sphere—so that the shaft and paddles are running free of contact with it in the middle—the machine slows down, and it cannot again attain full speed until the same conditions recur.

The rate of speed which may be worked up to as a maximum is determined by the position of the paddle-wheel, which is adjustable and floats upon the liquid although controlled in its circular motion by the shaft which passes through a square aperture in it and also a sleeve extending upward from it. The duty of the latter is to economise steam by cutting off the jet as soon as, by its rapidity of motion, the paddle-wheel has thrown the mercury to the sides to such an extent as to sink to a certain level in the centre.

Cheap motors coupled with cheap dynamos will, in the twentieth century, go far towards lightening the labours of millions whose toil is at present far too much of a mere mechanical nature. The dynamo itself, however, requires to be greatly reduced in first cost. Particularly it is necessary that the expense involved in drawing the wire, insulating it, and winding machines with it, should be diminished. This will no doubt be partly accomplished by the electrolytic producers of copper when once they get properly started on methods of depositing thin strips or wires of tough copper on to sheets of insulating material for wrapping round the magnets and other effective parts intended for dynamos. There is no fundamental reason which forbids that when electro deposition is resorted to for the recovery of a metal from its ore it should be straightway converted to the shape and to the purpose for which it is ultimately intended. This consideration has presented itself to the minds of some of the manufacturers of aluminium, who make many articles intended for household use electrolytically; and it must affect many other trades which are concerned in the output and in the working-up of metals readily susceptible of deposition—more particularly such as copper.

The familiar aneroid barometer furnishes a hint for another convenient form of small steam-engine. In seeking to cheapen machinery of this class it is of the utmost importance that the necessity for boring out cylinders and for planing and other expensive work should be avoided. In the aneroid barometer a shallow circular box is fitted with a cover, which is corrugated in concentric circles, and the pressure of the superincumbent air is caused to depress the centre of this cover through the device of partially exhausting the box of air and thus diminishing the internal resistance. To the slightly moving middle part of the cover is affixed a lever which actuates, after some intermediate action, the hand which moves on the dial to indicate, by its record of variations in the weight of the atmosphere, what the prospect of the weather may be.

In the aneroid form of the steam-engine the cylinder is immensely widened and flattened, and the broad circular lid, with its spiral corrugations, takes the place of the piston. The rod, which acts virtually as a piston-rod, is hollow, and it works into a bearing which permits the steam to escape when the extreme point of the stroke has been reached into a separate condensing chamber kept cool with water. The boiler itself, with corrugated top, may take the place of the cylinder.

In some respects this little machine represents a retrograde movement, even from Watt's original engine with its separate condenser; but its extreme economy of first cost recommends it to poor producers. In the near future no country homestead will be without its power installation of one kind or another, and there is room for many types of cheap motors.

A motor like the steam-turbine is evidently the forerunner of other engines designed to utilise the force of an emission jet of vapour or gas. There are very many processes in which gases generated by chemical combinations are permitted to escape without performing any services, not even that of giving up the energy which they may be made to store up when held in compression in a closed vessel.